Yamaha RX-V3800 Manuel télécharger pdf (Page 123)

119 En

Using multi-zone configuration

ADVANCED

OPERATION

English

3 Refer to “Selecting the input source of Zone

2 or Zone 3”, “Adjusting the volume level of

Zone 2 or Zone 3”, “Adjusting the balance of

the speaker level in Zone 2 or Zone 3” or

“Adjusting the tonal quality of Zone 2 or

Zone 3” on page 120 to perform further

operations.

Remote control operations

1 Set the operation mode selector to

AMP

and then press

SELECT k repeatedly to

select the zone you want to control.

“ZONE 2” or “ZONE 3” is displayed in the display

window (B) on the remote control.

2 Refer to “Selecting the input source of Zone

2 or Zone 3”, “Adjusting the volume level of

Zone 2 or Zone 3”, “Adjusting the balance of

the speaker level in Zone 2 or Zone 3” or

“Adjusting the tonal quality of Zone 2 or

Zone 3” on page 120 to perform further

operations.

3 Press

SELECT k / n to exit from the

Zone 2/Zone 3 mode.

■ Turning on or off Zone 2 and/or Zone 3

using the remote control

POWER and

STANDBY on the remote control

work differently depending on the selected zone that

appears in the display window (B) on the remote control.

• When the main zone, Zone 2 or Zone 3 mode is

selected (see page 119), you can turn on the main zone,

Zone 2 or Zone 3 or set them to the standby mode

individually.

• When the all mode is selected, pressing

POWER

turns on the main zone, Zone 2 and Zone 3

simultaneously and pressing

STANDBY sets them

to the standby mode simultaneously.

• When the remote control is in the main zone mode, “MAIN”

appears for a few seconds when

POWER or

STANDBY

is pressed.

• “ALL” appears in the display window (B) on the remote

control only when

SELECT n is pressed.

■ Selecting the input source of Zone 2 or

Zone 3

Rotate the

INPUT selector on the front panel

(or set the operation mode selector to

AMP

and then press one of the input selector buttons

(

)) to select the input source of the selected

zone.

If the remote control is used to select the input source, “2;

name of the selected input area” or “3; name of the

selected input area” is displayed in the display window

(B) on the remote control when Zone 2 or Zone 3 is

selected respectively.

• The selected input sources are shared across all zones.

• If you set the recording source other than “SOURCE” (see

page 70), the input source of Zone 2 is fixed to the source you

set as the recording source.

• This unit does not display the iPod or network/USB menu on

the video monitor connected to one of the ZONE VIDEO jacks.

• You must complete this step within 10 seconds while the

selected zone flashes in the front panel display. Otherwise, the

currently selected zone mode is automatically canceled. In this

case, press

ZONE CONTROLS on the front panel again.

• When a video monitor is connected to one of the ZONE VIDEO

jacks, you can display the control information of Zone 2 or

Zone 3 and XM Satellite Radio information on the video

monitor screen. Set “Zone OSD” to “Zone2&Zone3” or

“Zone2” (see page 96).

SELECT

SOURCE

AMP

Control mode Display window (B)

POWER

and

STANDBY

Main zone

mode

Name of the selected

input area

Turns on the main

zone only or sets it to

the standby mode.

Zone 2 mode

“ZONE 2” or “2;name

of the selected input

area”

Turns on Zone 2 or

sets it to the standby

mode.

Zone 3 mode

“ZONE 3” or “3;name

of the selected input

area”

Turns on Zone 3 or

sets it to the standby

mode.

All mode

“ALL”

POWER: turns on

the main zone, Zone

2 and Zone 3.

STANDBY: sets

the main zone, Zone

2 and Zone 3 to the

standby mode.

Notes

1 2 ... 118 119 120 121 122 123 124 125 126 127 128 ... 168 169

Commentaires sur ces manuels

Pas de commentaire

Yamaha RX-V3800 Manuel Page 123

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs AV Yamaha RX-V3800