Yamaha RX-V3800 Manuel Page 140
- Page / 169
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
136 En
Troubleshooting
During Auto Setup
After Auto Setup
• If the “ERROR” or “WARNING” screens appears, check the cause of the problem, then run “Auto Setup” again.
• If warning “W2” or “W3” appears, the adjustment are made, however the adjustments may not be optimal.
• Depending on the speakers, warning “W1” may appears even if the speakers connections are correct.
• If error “E10” occurs repeatedly, please contact a qualified Yamaha service center.
Error message Cause Remedy
See
page
E01:No Front SP Front L/R channel signals are not detected. Check the front L/R speaker connections. 15
E02:No Sur. SP A surround channel signal is not detected. Check the surround speaker connections. 15
E03:No PRNS SP A presence channel signal is not detected. Check the presence speaker connections. 15
E04:SBR→SBL Only right surround back channel signal is
detected.
Connect the surround back speaker to the
SURROUND BACK SINGLE terminal if
you only have one surround back speaker.
15
E05:Noisy Background noise is too loud. Try running “Auto Setup” in a quiet
environment.
—
Turn off noisy electric equipment like air
conditioners or move them away from the
optimizer microphone.
—
E06:Check Sur. Surround back speakers are connected,
though surround L/R speakers are not.
Connect surround speakers when you use
surround back speakers.
15
E07:No MIC The optimizer microphone was unplugged
during the “Auto Setup” procedure.
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front
panel.
37
E08:No Signal The optimizer microphone does not detect
test tones.
Check the microphone setting. 37
Check the speaker connections and
placement.
15
E09:User Cancel The “Auto Setup” procedure was cancelled
due to user activity.
Run “Auto Setup” again. 37
E10:Internal Err. An internal error occurred. Run “Auto Setup” again. 37
Warning message Cause Remedy
See
page
W1:Out of Phase Speaker polarity is not correct. This
message may appear depending on the
speakers even when the speakers are
connected correctly.
Check the speaker connections for proper
polarity (+ or –).
15
W2:Over Distance The distance between the speaker and the
listening position is over 24 m (80 ft).
Bring the speaker closer to the listening
position.
—
W3:Level Error The difference of volume level among
speakers is excessive.
Readjust the speaker installation so that all
speakers are set in locations with similar
conditions.
—
Check the speaker connections. 15
Use speakers of similar quality.
—
Adjust the output volume of the subwoofer. 37
W4:SP Mismatch The result of the wiring check of “Auto
Setup” is different from “Speaker Set” in
“Manual Setup”.
Use “Speaker Set” in “Manual Setup” to
adjust the speaker settings manually.
91
Notes
- RX-V3800 1
- Important safety instructions 2
- Caution-ii En 3
- Caution-iii En 4
- Contents 5
- About this manual 6
- Features 7
- Supplied accessories 8
- Getting started 9
- Quick start guide 10
- Indoor FM antenna 13
- AM loop antenna 13
- Open the lever 13
- Close the lever 13
- ■ After using this unit 14
- Connections 16
- Placing speakers 17
- ■ 6.1-channel speaker layout 18
- ■ 5.1-channel speaker layout 18
- Connecting speakers 19
- SPEAKERS 20
- Using presence speakers 21
- ■ Connecting the banana plug 23
- B, PR) video signals 24
- Information on HDMI™ 25
- Audio and video signal flow 26
- MONITOR OUT 27
- BD/HD DVD 28
- ■ Connecting a DVD player 29
- ■ Connecting a set-top box 30
- ■ Connecting audio components 31
- MULTI CH INPUT 33
- ■ Using REMOTE IN/OUT jacks 34
- Connecting the network 35
- Connecting the FM and AM 36
- Connecting the power cable 36
- Turning this unit on and off 37
- Using the remote control 38
- Front panel display 39
- DIGITAL PLUS 40
- Using the automatic setup 41
- (Auto Setup) 41
- Exit Detail 42
- Measurement Over 42
- Successfully 42
- Warning messages 43
- Playback 45
- Selecting audio input jacks 46
- (AUDIO SELECT) 46
- Selecting the MULTI CH INPUT 46
- Using your headphones 46
- Muting the audio output 47
- Playing video sources in the 47
- Using the sleep timer 47
- ■ Items in GUI screen 48
- Sound field programs 49
- ■ For audio music sources 50
- ■ For various sources 51
- ■ For visual sources of music 52
- ■ For movie sources 52
- ■ Stereo playback 53
- Using CINEMA DSP 3D mode 54
- Enjoying unprocessed input 54
- Using audio features 55
- Adjusting the speaker level 56
- 2-channel stereo 56
- FM/AM tuning 57
- Automatic preset tuning 58
- Manual preset tuning 58
- Selecting preset stations 59
- Exchanging preset stations 59
- XM™ Satellite Radio tuning 60
- 1 Rotate the 61
- ■ All Channel Search mode 62
- ■ Category Search mode 62
- ■ Preset Search mode 62
- ■ Direct Number Access mode 62
- Displaying the XM™ Satellite 64
- Radio information 64
- Using iPod™ 66
- Using Network/USB features 68
- ■ Remote control operation 69
- Using a PC server or Yamaha 70
- MCX-2000 70
- Using the Internet Radio 71
- USB portable audio player 72
- Using shortcut buttons 72
- (1-8) (6) 73
- Recording 74
- Advanced sound configurations 75
- SUR.DECODE 76
- Stereo/Surround 78
- (Stereo/Surround menu) 78
- “Yes” (see page 92) 79
- Rev. Delay 82
- Rev. Level 82
- The Compressed Music 83
- Enhancer mode 83
- Decoder parameter Features 84
- Input Select 85
- ■ I/O Assignment 86
- (Input/output assignment) 86
- ■ Decoder Mode (Decoder mode) 86
- Manual Setup (Volume) 88
- Manual Setup (Sound) 89
- ■ Tone Control (Tone control) 90
- ■ Lipsync 91
- ■ Channel Mute (Channel mute) 92
- Manual Setup (Video) 93
- Short Message 94
- On Screen 94
- Position 94
- Wall Paper 94
- Manual Setup (Basic) 95
- Manual Setup (NET/USB) 98
- Manual Setup (Option) 100
- ■ Zone2 Set/Zone3 Set 101
- (Zone 2/Zone 3 setting) 101
- Signal Info 102
- (Input signal information) 102
- Language 103
- 1 Press 104
- SYSTEM MEMORY 105
- Using examples 106
- CLASSICAL LIVE/CLUB 108
- ENTERTAIN 108
- Remote control features 109
- Set to SOURCE 110
- Setting remote control codes 111
- Programming codes from other 113
- Changing source names in the 114
- Macro programming features 115
- ■ Default macro functions 116
- 4 Press 117
- Clearing configurations 118
- 2 Press 119
- 3 Press and hold 119
- 2 Press and hold 120
- 3 Press 120
- ■ Using external amplifiers 121
- Controlling Zone 2 or Zone 3 122
- Advanced setup 126
- ■ Wake on RS-232C access 127
- ■ Remote control AMP ID 127
- ■ Remote control TUNER ID 128
- Troubleshooting 131
- ADDITIONAL 133
- INFORMATION 133
- ■ Remote control 135
- ■ Network and USB 136
- ■ Auto Setup 139
- During Auto Setup 140
- After Auto Setup 140
- Resetting the system 141
- Glossary 142
- ■ Frequency 147
- ■ Q factor 147
- Specifications 148
- ■ HDMI signal compatibility 149
- ■ Numerics 150
- DEFG H IJ MKL 154
- GPL/LGPL 158
- APPENDIX 159
- MODIFICATION 160
- List of remote control codes 162
- SATELLITE TUNER 163
- TAPE DECK 163
- Printed in Malaysia 169
Produits connexes et manuels pour Récepteurs AV Yamaha RX-V3800
Récepteurs AV Yamaha RX-Z1 Manuel
(95 pages)
(95 pages)
Récepteurs AV Yamaha RX-V565 Manuel
(76 pages)
(76 pages)
(323 pages)
Récepteurs AV Yamaha RX-V1 Manuel
(95 pages)
(95 pages)
Récepteurs AV Yamaha RX-V740 Manuel
(71 pages)
(71 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.687 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels