Yamaha RX-V1065 Manuel Page 69
- Page / 102
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
66 En
APPENDIX
Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized
Yamaha dealer or service center.
Troubleshooting
General
Problem Cause Remedy
See
page
This unit does not
operate properly.
The internal microcomputer is frozen due
to an external electric shock (such as
lightning or excessive static electricity) or
by a drop in power supply voltage.
Disconnect the power cable from the AC wall outlet,
wait about 30 seconds and then plug it in again.
—
This unit suddenly
enters the standby
mode
The internal temperature is too high and
the overheat protection circuitry has been
activated.
Wait about 1 hour for this unit to cool down and then
turn it back on.
—
The protection circuitry has been activated
because of a short circuit, etc.
Check that the speaker impedance setting is correct. 64
Check that the speaker wires are not touching each
other and then turn this unit back on.
—
The sleep timer has turned off this unit. Turn on this unit and play the source again. —
This unit fails to turn
on or enters the
standby mode soon
after the power is
turned on.
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable properly to an AC wall
outlet.
18
The speaker impedance setting is
incorrect.
Set the speaker impedance to match your speakers. 64
(When this unit is turned back on and
“CHECK SP WIRES!” is displayed.) The
protection circuitry has been activated
because this unit was turned on while a
speaker cable was shorted.
Make sure that all speaker cables between this unit
and speakers are connected properly.
11
This unit cannot be
turned off.
The internal microcomputer is frozen due
to an external electric shock (such as
lightning or excessive static electricity) or
by a drop in power supply voltage.
Disconnect the power cable from the AC wall outlet,
wait about 30 seconds and then plug it in again.
—
No picture. An appropriate video input is not selected
on the video monitor.
Select an appropriate video input on the video
monitor.
—
The external video component is
connected to one of the HDMI 1-4 jacks
while your video monitor is connected to
the MONITOR OUT (COMPONENT
VIDEO or VIDEO) jacks.
Connect the external video component to the video
input jacks other than the HDMI 1-4 jacks or connect
the video monitor to the HDMI OUT jack.
14, 15
This unit outputs the video signals not
supported by the video monitor connected
to the HDMI OUT jack.
Displays the advanced setup menu and select
“VIDEO” in “INIT” to reset the video parameters.
64
Displays the advanced setup menu and set
“MON.CHK” to “YES”.
64
Video signals are input from a game
console while your video monitor is
connected to the HDMI OUT jack.
Connect the video monitor to the MONITOR OUT
(COMPONENT VIDEO) jacks.
14
Non-standard video signals are input. Connect the video monitor to the MONITOR OUT
(COMPONENT VIDEO or VIDEO) jacks.
14
- RX-V1065 1
- IMPORTANT SAFETY INSTRUCTIONS 2
- Caution-ii En 3
- Contents 4
- INTRODUCTION 5
- About this manual 6
- Supplied accessories 6
- Part names and functions 7
- Rear panel 8
- Remote control 10
- Quick start guide 11
- Using the remote control 12
- Placing speakers 13
- Connecting speakers 14
- Connections 15
- R) components 16
- TV, or projector 17
- Digital output 17
- (optical) 17
- Connecting other components 18
- CENTERSINGLE 19
- Using the VIDEO AUX jacks 20
- Connecting the power cable 21
- Turning this unit on and off 21
- Using Auto Setup 22
- Basic procedure 25
- Using the SCENE function 25
- Select Scene 26
- BD/DVD TV CD RADIO 26
- Using your headphones 27
- Program name 28
- Sound field program category 28
- (Frequency tuning) 32
- 01:FM92.5MHz 33
- Front panel display 35
- (sold separately) 36
- XM Satellite Radio 37
- operations 37
- 00880's 38
- P01:---<<008 38
- 008 80's 38
- Back to “Channel” 39
- 184Weather 40
- Category 41
- Category name 41
- 001Hits1 42
- P01:---<<001 42
- 001 Hits 1 42
- Setting the Parental Lock 43
- Radio™ information 44
- Controlling iPod™ 45
- Shuffle/repeat playback 46
- Playback of the Bluetooth™ 47
- Using the sleep timer 49
- Option menu items 50
- Sound field parameters 53
- Adjustable range: 0.1 to 2.0 54
- Adjustable range: 0 to 10 54
- Decoder parameters 56
- Speaker Setup 58
- Sound Setup 60
- Function Setup 61
- DSP Parameter 63
- Memory Guard 63
- Connecting Zone2 64
- Controlling Zone2 65
- Setting remote control codes 66
- Updating the firmware 67
- Setting a remote control ID 67
- Advanced setup 68
- APPENDIX 69
- Troubleshooting 70
- Tuner (FM/AM) 72
- Bluetooth™ 77
- Auto Setup (YPAO) 78
- After Auto Setup 79
- Glossary 80
- Information on HDMI™ 84
- Specifications 85
- List of remote control codes 89
- Blu-ray Disc 95
- DVD Recorder 95
- Sattelite 96
- Printed in Malaysia WQ95040 100
- Video;;;;;;Off 101
- Information about software 102
Produits connexes et manuels pour Récepteurs AV Yamaha RX-V1065
(574 pages)
Récepteurs AV Yamaha HTR-5835 Manuel
(81 pages)
(81 pages)
Récepteurs AV Yamaha CRX-330 Manuel
(32 pages)
(32 pages)
Récepteurs AV Yamaha HTR-3063 Manuel
(57 pages)
(57 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.539 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels