Yamaha DSP-AX1 Manuel du propriétaire Page 22
- Page / 256
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
20
Preparations
Connecting Speakers
This section explains how to connect speakers to the DSP-AX1. After you finish connecting your speakers, use the SET MENU to change
the signal output settings according to the number and size of the speakers in your configuration.
■ Using Speaker Cords
A speaker cord is actually a pair of insulated cables running side by side. One of
the cables is colored or shaped differently, perhaps with a stripe, groove or ridge.
To make sure you always connect speakers with the correct polarity, determine
the difference between the cables of your speaker cord, make a note of which
cable you plan to use for which polarity (+ and –), and always connect the speaker
cords consistently.
1
1
Strip off 9 mm (3/8 in.) of insulation from the ends of the cables.
2
2
Twist the exposed wires of the cable together to prevent short
circuits.
3
3
Loosen the terminal knob by turning it counterclockwise.
4
4
Insert only the exposed portion of the cable into the slot in the side of
the terminal, and tighten the terminal knob.
Note:
• If your speaker cords have banana plugs, tighten the terminal knob and insert the
plug into the end of the terminal. (Except for Europe and UK Models)
Caution:
• Connect the speaker cords with care to avoid creating a short circuit. If you turn on
the power and there is a short circuit, this unit may be damaged even though the
protection circuit automatically shuts off the power.
■ Connecting the Main Speakers
Before connecting any speaker cords, identify which terminals are for the right
and left channels and also the + and – polarities. If you connect speakers with the
wrong polarity (+ to –), the DSP-AX1 will not reproduce clear sound.
Connect the + and – terminals of your right and left Main speakers to
the L and R MAIN + and – terminals on this unit.
■ Connecting the Center Speaker
Connect the + terminal of your Center speaker to the CENTER +
terminal and the – terminal of your Center speaker to the CENTER –
terminal.
Hookups
AMAINB
+
–
+
–
+
–
S
PEAKERS
FRONT
REAR
CENTER REAR CENTER
+
–
+
–
+
–
+
–
+
–
+
–
BANANA PLUG
[Except for Europe and UK models]
Right Main
Speaker A
Left Main
Speaker A
Right Main
Speaker B
Left Main
Speaker B
Center Speaker
- OWNER’S MANUAL 1
- MODE D’EMPLOI 1
- BEDIENUNGSANLEITUNG 1
- For U.K. customers 2
- Contents 3
- Introduction 4
- Features 5
- Checking the Package Contents 7
- Front Panel 8
- Remote Control 10
- Controls and Functions 11
- Front Panel Display 12
- Rear Panel 13
- Preparations 14
- Speaker System Configurations 15
- Speaker Placement 16
- Connecting to Digital Jacks 17
- About the Video Jacks 17
- Connecting Audio Components 18
- ■ Connecting a Tape Deck 19
- Connecting Video Components 20
- ■ Connecting a VCR 21
- ■ Connecting a DVD Player 21
- ■ Connecting a Video Monitor 21
- Connecting Speakers 22
- SPLIT jacks using pin plugs 23
- ■ Connecting a Rear Subwoofer 24
- ■ Impedance Selector switch 24
- (SURROUND) 25
- Connecting Power Supply Cords 26
- OSD Modes 27
- Selecting the OSD Mode 27
- Speaker Settings 28
- Before You Begin 29
- DSP Test 31
- Basic Operation 32
- Power Control 33
- Selecting a Source 34
- Input Modes and Indications 35
- Basic Playback 36
- Advanced Operation 38
- SET MENU Items 39
- Operating the SET MENU 40
- 2. LOW FREQ. TEST 44
- 5. SP DELAY TIME 46
- 6. AUDIO DELAY 46
- 4. DTS SET 46
- 9. CINEMA EQ 48
- 13. MEMORY GUARD 50
- 15. INPUT MODE 50
- 16. INPUT RENAME 51
- 17. DIMMER 51
- 18. ZONE 2 SET 51
- Using the Remote Control 52
- Remote Control Features 53
- Each Component Control Area 54
- 5~10 cm (2 to 4 in.) 60
- Using the Macro Feature 61
- Connections 66
- Remote Control in ZONE 2 67
- Additional Information 68
- Understanding Sound Fields 69
- Recreating a Sound Field 69
- E/R (Early Reflection) 69
- Movie Theater Programs 72
- ■ Program Groups 7~9 73
- ■ Program Groups 10~12 73
- Changing Parameter Settings 75
- EFCT TRIM (Effect Trim) 76
- INIT. DLY (Initial Delay) 76
- S. DLY (Surround Delay) 77
- ROOM SIZE 77
- LIVENESS 78
- Appendix 80
- Troubleshooting 81
- Specifications 85
- Table des matières 87
- Particularités 89
- Face avant 92
- Commandes et fonctions 93
- Boîtier de télécommande 94
- Afficheur de la face avant 96
- Panneau arrière 97
- Remarque: 100
- Attention: 101
- R/CRPB/CBY 101
- Remarques: 103
- Raccordements 105
- Raccordement des enceintes 106
- Modes d’affichage sur l’écran 111
- Choix du mode d’affichage 111
- Réglages des enceintes 112
- Avant de commencer 113
- Essai Dolby Surround 114
- Essai DSP 115
- Opérations de base 116
- Commande de l’alimentation 117
- Choix de la source 118
- Modes d’entrée et indications 119
- Lecture standard 120
- Préparatifs 121
- Fonctionnement détaillé 122
- Paramètres de SET MENU 123
- Utilisation de SET MENU 124
- 6. AUDIO DELAY (Retard audio) 130
- 4. DTS SET (Réglage DTS) 130
- 17. DIMMER (luminosité) 135
- Une pression sur la touche % 137
- Une pression sur la touche fi 137
- Fonctionnement 138
- Français 139
- 5 à 10 cm 144
- Ces deux indications 144
- Emploi des macros 145
- ■ Création d’une macro 146
- ■ Enregistrement d’une macro 146
- V-AUX TAPE PHONO 147
- D-TV CBL/SAT TUNER MD CD 147
- VCR 1 VCR 2 VCR 3 LD DVD 147
- ON SCREEN 149
- SLEEP TEST 149
- Informations complémentaires 152
- Qu’est-ce qu’un champ sonore? 153
- Restitution d’un champ sonore 153
- E/R (Premières réflexions) 153
- Hi-Fi DSP-Sound Field Program 154
- CINEMA-DSP 155
- Corrections pour les films 156
- ■ Groupes 7 à 9 de correction 157
- INIT. DLY (Retard initial) 160
- S. DLY (Retard de l’ambiance) 161
- LIVENESS (Vivacité) 162
- Guide de dépannage 79 164
- Guide de dépannage 165
- Caractéristiques techniques 169
- Einleitung 172
- Merkmale 173
- Verwendung der Fernbedienung 175
- Fronttafel 176
- Fernbedienung 178
- Fronttafel-Display 180
- Rückwand 181
- Vorbereitungen 182
- ( ) 183
- Hinweis: 184
- Hinweise: 186
- Anschlüsse 191
- Bevor Sie beginnen 197
- Dolby Surround Test 198
- DSP-Test 199
- Grundlegende 200
- Bedienung 200
- Wahl einer Signalquelle 202
- Eingangsmodi und Anzeigen 203
- Vorsicht: 205
- Weiterführende 206
- PARAMETER 208
- SET MENU 208
- KeinKlein 209
- Groß Klein 209
- ■ Über den Testton 212
- ■ 3A. LFE LEVEL (LFE-Pegel) 213
- 4. DTS SET (DTS-Einstellung) 214
- 9. CINEMA EQ (Kino-Entzerrer) 216
- 12. 6.1/ES AUTO 217
- 17. DIMMER (Abblendung) 219
- Funktionen der Fernbedienung 221
- Zusätzliche Informationen 236
- Verstehen von Sound-Feldern 237
- HiFi DSP-Sound-Feld-Programm 238
- Filmtheater-Programme 240
- Programmtyp (Unterprogramm) 243
- Cursor Parameter 243
- ROOM SIZE (Raumgröße) 245
- Störungsbeseitigung 79 248
- Technische Daten 83 248
- Störungsbeseitigung 249
- Technische Daten 253
- V482940-1Printed in Japan 254
- Quick Reference Card 255
Produits connexes et manuels pour Récepteurs AV Yamaha DSP-AX1
Récepteurs AV Yamaha RX-V3800 Manuel
(459 pages)
(459 pages)
Récepteurs AV Yamaha RX-V765 Manuel
(156 pages)
(156 pages)
Récepteurs AV Yamaha RX-V1900 Manuel
(506 pages)
(506 pages)
Récepteurs AV Yamaha RX-A3010 Manuel
(157 pages)
(157 pages)
(441 pages)
(92 pages)
(18 pages)
Récepteurs AV Yamaha HTR-5650 Manuel
(66 pages)
(66 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.505 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels