Yamaha CL3 Manuel du propriétaire Page 56
- Page / 65
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Specifications
Owner’s Manual
56
Input/output characteristics
ANALOG INPUT CHARACTERISTICS
*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum
gain. (all faders and level controls are maximum position.)
*2. XLR-3-31 type connectors are balanced. (1= GND, 2= HOT, 3= COLD)
*3. In these specifications, 0dBu= 0.775 Vrms.
*4. All input AD converters are 24bit linear, 128times oversampling.
*5. +48V DC ( phantom power ) is supplied to OMNI IN (1-8) and TALKBACK XLR type connectors via each individual software controlled
switches.
ANALOG OUTPUT CHARACTERISTICS
*1. XLR-3-32 type connectors are balanced. (1= GND, 2= HOT, 3= COLD)
*2. PHONES stereo phone jack is unbalanced. (Tip= LEFT, Ring= RIGHT, Sleeve= GND)
*3. In these specifications, 0dBu= 0.775 Vrms.
*4. All output DA converters are 24bit, 128times oversampling.
*5. There are switches inside the body to preset the maximum output level.
*6. The position of the level control is 10dB lowered from Max.
DIGITAL INPUT & OUTPUT CHARACTERISTICS
DIGITAL OUTPUT CHARACTERISTICS
*1. XLR-3-32 type connectors are balanced. (1= GND, 2= HOT, 3= COLD)
I/O SLOT (1-3) CHARACTERISTICS
Each I/O Slot accepts a mini-YGDAI card. Only Slot1 has a serial interface.
CONTROL I/O CHARACTERISTICS
*1. Input pin: TTL level, w/ internal pull-up (47kΩ)
Output pin: Open drain output (Vmax=12V, maximum sink current/pin=75mA)
Power supply pin: Output voltage Vp=5V, Max. output current Imax=300mA
*2. 4pin= +12V, 3pin= GND, Lamp rating 5W. Voltage control by software.
Input
Terminals
GAIN
Actual Load
Impedance
For Use With
Nominal
Input Level
Connector
Sensitivity
*1
Nominal Max. before clip
OMNI IN 1-8
+66dB
7.5kΩ
50-600Ω Mics
& 600Ω Lines
–82dBu (61.6μV) –62dBu (0.616mV) –42dBu (6.16mV) XLR-3-31 type
(Balanced)
*2
–6dB –10dBu (245mV) +10dBu (2.45V) +30dBu (24.5V)
TALKBACK
+64dB
10kΩ
50-600Ω Mics
& 600Ω Lines
–70dBu (0.245mV) –60dBu (0.775mV) –40dBu (7.75mV) XLR-3-31 type
(Balanced)
*2
+20dB –26dBu (38.8mV) –16dBu (0.123V) +4dBu (1.23V)
Output
Terminals
Actual Source
Impedance
For Use With
Nominal
GAIN SW
*5
Output Level
Connector
Nominal Max. before clip
OMNI OUT 1-8 75Ω 600Ω Lines
+24dB (default) +4dBu (1.23V) +24dBu (12.3V) XLR-3-32 type
(Balanced)
*1
+18dB –2dBu (616mV) +18dBu (6.16V)
PHONES 15Ω
8Ω Phones –
75mW
*6
150mW
Stereo Phone Jack (TRS)
(Unbalanced)
*2
40Ω Phones –
65mW
*6
150mW
Terminal Format Data length Level Audio Connector
Primary/Secondary Dante 24bit or 32bit 1000Base-T 64ch Input/64ch Output @48kHz EtherCON Cat5e
Terminal Format Data Length Level Connector
DIGITAL OUT AES/EBU AES/EBU Professional Use 24bit RS422
XLR-3-32 type (Balanced)
*1
Terminal Format Level Connector
MIDI
IN MIDI – DIN Connector 5P
OUT MIDI – DIN Connector 5P
WORD CLOCK
IN – TTL/75Ω terminated BNC Connector
OUT – TTL/75Ω BNC Connector
GPI (5IN/5OUT) – –
D Sub Connector 15P (Female)
*1
NETWORK IEEE802.3 10BASE-T/100Base-TX RJ-45
LAMP (CL5: x3, CL3: x2, CL1: x1) –
0V-12V
*4
XLR-4-31 type
*2
USB HOST USB 2.0 – USB A Connector (Female)
DC POWER INPUT – – JL05 Connector
METER (CL3/CL1 only) – – D Sub Connector 9P (Female)
- Owner’s Manual 1
- Contents 2
- IMPORTANT SAFETY INSTRUCTIONS 3
- FCC INFORMATION (U.S.A.) 4
- PRECAUTIONS 5
- Information 6
- Introduction 7
- Features 8
- About the models 9
- Controls and functions 10
- Channel Strip section 11
- SELECTED CHANNEL section 12
- Display section 13
- Centralogic section 13
- SCENE MEMORY/MONITOR section 14
- USER DEFINED KNOBS 14
- USER DEFINED KEYS 14
- Master section 15
- USB connector 15
- Meter section (for CL5 only) 15
- Front Panel 16
- Rear Panel 16
- Basic touch screen 18
- The on-screen user interface 18
- List windows 19
- Keyboard window 19
- Popup windows 19
- Dialog boxes 19
- Viewing the touch screen 20
- Entering names 21
- Using the tool buttons 22
- 1 2 3 4 5 22
- Using libraries 23
- Channel select button 24
- Selected region 24
- 3 RECALL button 25
- 1 STORE button 25
- Initializing settings 26
- Copying/pasting settings 26
- Comparing two settings 27
- Controlling selected 28
- CHANNEL section) 28
- Using the top panel 29
- (Channel Strip section) 29
- 1 ON FADER switch button 30
- Connections 31
- Audio input/output 32
- Installing an option card 33
- Owner’s Manual 34
- Word clock connections and 35
- Making HA (Head Amp) 36
- Sending an input channel 37
- TO STEREO/MONO field 38
- Connecting the devices 39
- Setting the input channels 40
- GAIN knob 40
- Applying EQ/dynamics 41
- Setting the output channels 41
- Using GEQ 41
- Applying effects 42
- Changing the patch settings 44
- Grouping and linking 45
- Setting a custom fader bank 46
- Using talkback 46
- Routing the oscillator to an 47
- Using scene memories 47
- Recording and playing audio 48
- Saving and loading the unit 49
- Initializing the unit to 50
- Restoring the current scene 50
- Adjusting the faders 51
- (Calibration function) 51
- Troubleshooting 52
- Installing the 54
- MBCL meter 54
- General specifications 55
- Input/output characteristics 56
- Pin Assignment 57
- Dimensions 58
- Block Diagram 61
- CUE / MONITOR 62
- Level Diagram 63
Produits connexes et manuels pour Mélangeurs audio Yamaha CL3
(163 pages)
(24 pages)
Mélangeurs audio Yamaha MX200 Spécifications
(57 pages)
(57 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.145 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels