Yamaha RX-V1800 Manuel du propriétaire Page 121
- Page / 151
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
119 En
Troubleshooting
ADDITIONAL
INFORMATION
English
The audio input
sources cannot be
played in the desired
digital audio signal
format. (Desired input
source indicator or
decoder indicator in
the front panel
display does not light
up.)
The connected component is not set to
output the desired digital audio signals.
Make an appropriate setting following the operating
instructions for your component.
—
Audio input jack select is set to
“ANALOG”.
Set the audio input jack select to “AUTO”.
43
A humming sound is
heard.
Incorrect cable connections. Connect the audio cables firmly. If the problem
persists, the cables may be defective.
—
No connection from the turntable to the
GND terminal.
Connect the grounding cable of the turntable to the
GND terminal of this unit.
28
The volume level is
low while a record is
being played.
The record is being played on a turntable
with an MC cartridge.
Connect your turntable to this unit through an MC-
head amplifier.
28
The volume level
cannot be increased,
or the sound is
distorted.
The component connected to the AUDIO
OUT (REC) jacks of this unit is turned
off.
Turn on the power of the component.
—
The sound effect
cannot be recorded.
It is not possible to record the sound effect
with a recording component.
A source cannot be
recorded by a digital
recording component
connected to the
DIGITAL OUTPUT
jack.
The source component is not connected to
the DIGITAL INPUT jacks of this unit.
Connect the source component to the DIGITAL
INPUT jacks.
25, 28
Some components cannot record Dolby
Digital or DTS sources.
A source cannot be
recorded by an
analog component
connected to the
AUDIO OUT (REC)
jacks.
The source component is not connected to
the analog AUDIO IN jacks of this unit.
Connect the source component to the analog AUDIO
IN jacks.
28
The sound field
parameters and some
other settings of this
unit cannot be
changed.
“MEMORY GUARD” in “SET MENU”
is set to “ON”.
Set “MEMORY GUARD” to “OFF”.
90
This unit does not
operate properly.
The internal microcomputer has been
frozen by an external electric shock (such
as lightning or excessive static electricity)
or by a power supply with low voltage.
Disconnect the power cable from the AC wall outlet
and then plug it in again after about 30 seconds.
—
“CHECK SP WIRES”
appears in the front
panel display.
Speaker cables are short-circuited. Make sure all speaker cables are connected correctly.
16
There is noise
interference from
digital or radio
frequency equipment.
This unit is too close to the digital or high-
frequency equipment.
Move this unit further away from such equipment.
—
The picture is
disturbed.
The video source uses scrambled or
encoded signals to prevent dubbing.
This unit suddenly
enters the standby
mode.
The internal temperature becomes too
high and the overheat protection circuitry
has been activated.
Wait about 1 hour for this unit to cool down and then
turn it back on.
—
Problem Cause Remedy
See
page
- RX-V1800 1
- ■ For U.K. customers 2
- Contents 3
- About this manual 4
- Features 5
- Supplied accessories 6
- Getting started 7
- Step 1: Set up your speakers 9
- COMPONENT VIDEO 10
- For further connections 11
- ■ After using this unit 12
- Quick start guide 13
- Connections 14
- Placing speakers 15
- ■ 6.1-channel speaker layout 16
- ■ 5.1-channel speaker layout 16
- 1.8 m (6 ft) 17
- PREPARATION 19
- ■ Connecting the banana plug 21
- ■ Audio jacks 22
- ■ Video jacks 22
- Information on HDMI™ 23
- Audio and video signal flow 25
- MONITOR OUT 26
- Connecting other components 27
- ■ Using REMOTE IN/OUT jacks 33
- Connecting the FM and AM 34
- Connecting the power cable 34
- AC OUTLETS 34
- Setting the speaker impedance 35
- Turning this unit on and off 35
- Front panel display 36
- DIGITAL PLUS 37
- Using the remote control 38
- Using AUTO SETUP 39
- 5 Press 40
- 2 Press 42
- Playback 44
- Selecting audio input jacks 45
- (AUDIO SELECT) 45
- Selecting the MULTI CH INPUT 45
- Using your headphones 45
- Muting the audio output 46
- Displaying the input source 46
- Playing video sources in the 47
- Using the sleep timer 47
- Sound field programs 48
- ■ For audio music sources 49
- ■ For various sources 50
- ■ For visual sources of music 51
- ■ For movie sources 51
- ■ Stereo playback 52
- ■ Compressed Music Enhancer 52
- Enjoying unprocessed input 53
- Using audio features 54
- Adjusting the speaker level 55
- 2-channel stereo 55
- FM/AM tuning 56
- Automatic preset tuning 57
- Manual preset tuning 57
- Selecting preset stations 58
- Exchanging preset stations 59
- Frequency display 60
- Using the enhanced other 62
- Using iPod™ 63
- 1 Press 64
- Recording 65
- Advanced sound configurations 66
- REV.TIME 70
- REV.DELAY 70
- REV.LEVEL 70
- Selecting decoders 71
- ■ Decoder descriptions 72
- ■ Auto setup AUTO SETUP 74
- ■ Manual setup MANUAL SETUP 74
- Input menu 4 INPUT MENU 76
- Option menu 5 OPTION MENU 76
- A)DISPLAY SET 76
- ■ System memory SYSTEM MEMORY 77
- Using SET MENU 78
- 1 BASIC MENU 79
- ■ Test tone D)TEST TONE 82
- 2 VOLUME MENU 83
- 3 SOUND MENU 84
- ■ Low-frequency effect level 85
- (Lip sync) 86
- ■ Audio settings E)AUDIO SET 86
- 4 INPUT MENU 87
- 5 OPTION MENU 90
- ■ Video settings B)VIDEO SET 91
- ■ Memory guard C)MEMORY GUARD 92
- ■ Zone set E)ZONE SET 93
- SYSTEM MEMORY 96
- Using examples 97
- Set to SOURCE 100
- Setting remote control codes 101
- Remote control features 102
- Programming codes from other 103
- Changing source names in the 104
- Macro programming features 105
- ■ Default macro functions 106
- 2 Press the 107
- 4 Press 107
- Clearing configurations 108
- ■ Clearing a macro function 109
- ■ Using external amplifiers 110
- Controlling Zone 2 or Zone 3 111
- 3 Press 112
- (except Europe model) 114
- Advanced setup 115
- Troubleshooting 119
- ADDITIONAL 121
- INFORMATION 121
- DEVICE OVER 122
- HDCP ERROR 122
- Resolution 122
- ■ Remote control 123
- ■ AUTO SETUP 124
- Resetting the system 126
- Glossary 127
- ■ PCM (Linear PCM) 130
- ■ S-video signal 130
- ■ Frequency 132
- ■ Q factor 132
- Specifications 133
- Фронтальная панель 140
- Afstandsbediening/Пульт ДУ 141
- HD DVD PLAYER 144
- Blu-lay Disc player 144
- APPENDIX 147
- Printed in Malaysia 151
Produits connexes et manuels pour Récepteurs AV Yamaha RX-V1800
Récepteurs AV Yamaha YHT-S401 Manuel
(70 pages)
(70 pages)
Récepteurs AV Yamaha RX-V767 Manuel
(133 pages)
(133 pages)
(538 pages)
Récepteurs AV Yamaha HTR-4063 Manuel
(97 pages)
(97 pages)
(58 pages)
Récepteurs AV Yamaha RX-V650 Manuel
(91 pages)
(91 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.140 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels