Yamaha RX-V1800 Manuel du propriétaire Page 120
- Page / 151
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
118 En
Troubleshooting
Short message
displays do not
appear on the video
monitor.
“SHORT MESSAGE” is set to “OFF”. Set “SHORT MESSAGE” to “ON”.
88
“GRAY BACK” is set to “OFF”. Set “GRAY BACK” to “AUTO”.
88
“VIDEO CONV.” is set to “OFF”. Set “VIDEO CONV.” to “ON”.
89
The signals input at the HDMI input jacks
are being output at the HDMI OUT jack.
Video signals in the progressive format or
HDTV video signals are being input.
The sound suddenly
goes off.
The protection circuitry has been activated
because of a short circuit, etc.
Check that the speaker impedance setting is correct.
33, 113
Check that the speaker wires are not touching each
other and then turn this unit back on.
—
The sleep timer has turned off this unit. Turn on this unit, and play the source again.
—
The sound is muted.
Press
D
MUTE or
B
VOLUME +/– on the remote
control to resume audio output.
44
Sound is heard from
the speaker on one
side only.
Incorrect cable connections. Connect the cables properly. If the problem persists,
the cables may be defective.
16
Incorrect settings in “SPEAKER
LEVEL”.
Adjust the “SPEAKER LEVEL” settings.
79
Only the center
speaker outputs
substantial sound.
When playing a monaural source with a
CINEMA DSP program, the source signal
is directed to the center channel, and the
front and surround speakers output effect
sounds.
No sound is heard
from the center
speaker.
“CENTER SP” in “SET MENU” is set to
“NONE”.
Set “CENTER SP” to “SMALL” or “LARGE”.
77
One of the HiFi DSP programs (except for
“7ch Stereo”) has been selected.
Try another sound field program.
46
No sound is heard
from the presence
speakers.
The sound field programs are turned off.
Press
O
STRAIGHT to turn them on.
51
You are using a source or program
combination that does not output sound
from all channels.
Try another sound field program.
42
No sound is heard
from the surround
speakers.
“SUR. L/R SP” in “SET MENU” is set to
“NONE”.
Set “SUR. L/R SP” to “SMALL” or “LARGE”.
78
This unit is in the “STRAIGHT” mode
and a monaural source is being played
back.
Press
O
STRAIGHT on the front panel so that
“STRAIGHT” disappears from the front panel
display.
51
Speakers are connected to the
SURROUND BACK speaker terminals.
Connect the surround speakers to the SURROUND
speaker terminals.
51
No sound is heard
from the subwoofer.
“LFE/BASS OUT” in “SET MENU” is
set to “FRONT” when a Dolby Digital or
DTS signal is being played.
Set “LFE/BASS OUT” to “SWFR” or “BOTH”.
77
“LFE/BASS OUT” in “SET MENU” is
set to “SWFR” or “FRONT” when a 2-
channel source is being played.
Set “LFE/BASS OUT” to “BOTH”.
77
The source does not contain low-
frequency signals.
No sound is heard
from the surround
back speakers.
“SUR. L/R SP” in “SET MENU” is set to
“NONE” and “SUR.B L/R SP” is
automatically set to “NONE”.
Set “SUR. L/R SP” and “SUR.B L/R SP” to a setting
other than “NONE”.
78
“SUR.B L/R SP” in “SET MENU” is set
to “NONE”.
Set “SUR.B L/R SP” to a setting other than “NONE”.
78
Problem Cause Remedy
See
page
- RX-V1800 1
- ■ For U.K. customers 2
- Contents 3
- About this manual 4
- Features 5
- Supplied accessories 6
- Getting started 7
- Step 1: Set up your speakers 9
- COMPONENT VIDEO 10
- For further connections 11
- ■ After using this unit 12
- Quick start guide 13
- Connections 14
- Placing speakers 15
- ■ 6.1-channel speaker layout 16
- ■ 5.1-channel speaker layout 16
- 1.8 m (6 ft) 17
- PREPARATION 19
- ■ Connecting the banana plug 21
- ■ Audio jacks 22
- ■ Video jacks 22
- Information on HDMI™ 23
- Audio and video signal flow 25
- MONITOR OUT 26
- Connecting other components 27
- ■ Using REMOTE IN/OUT jacks 33
- Connecting the FM and AM 34
- Connecting the power cable 34
- AC OUTLETS 34
- Setting the speaker impedance 35
- Turning this unit on and off 35
- Front panel display 36
- DIGITAL PLUS 37
- Using the remote control 38
- Using AUTO SETUP 39
- 5 Press 40
- 2 Press 42
- Playback 44
- Selecting audio input jacks 45
- (AUDIO SELECT) 45
- Selecting the MULTI CH INPUT 45
- Using your headphones 45
- Muting the audio output 46
- Displaying the input source 46
- Playing video sources in the 47
- Using the sleep timer 47
- Sound field programs 48
- ■ For audio music sources 49
- ■ For various sources 50
- ■ For visual sources of music 51
- ■ For movie sources 51
- ■ Stereo playback 52
- ■ Compressed Music Enhancer 52
- Enjoying unprocessed input 53
- Using audio features 54
- Adjusting the speaker level 55
- 2-channel stereo 55
- FM/AM tuning 56
- Automatic preset tuning 57
- Manual preset tuning 57
- Selecting preset stations 58
- Exchanging preset stations 59
- Frequency display 60
- Using the enhanced other 62
- Using iPod™ 63
- 1 Press 64
- Recording 65
- Advanced sound configurations 66
- REV.TIME 70
- REV.DELAY 70
- REV.LEVEL 70
- Selecting decoders 71
- ■ Decoder descriptions 72
- ■ Auto setup AUTO SETUP 74
- ■ Manual setup MANUAL SETUP 74
- Input menu 4 INPUT MENU 76
- Option menu 5 OPTION MENU 76
- A)DISPLAY SET 76
- ■ System memory SYSTEM MEMORY 77
- Using SET MENU 78
- 1 BASIC MENU 79
- ■ Test tone D)TEST TONE 82
- 2 VOLUME MENU 83
- 3 SOUND MENU 84
- ■ Low-frequency effect level 85
- (Lip sync) 86
- ■ Audio settings E)AUDIO SET 86
- 4 INPUT MENU 87
- 5 OPTION MENU 90
- ■ Video settings B)VIDEO SET 91
- ■ Memory guard C)MEMORY GUARD 92
- ■ Zone set E)ZONE SET 93
- SYSTEM MEMORY 96
- Using examples 97
- Set to SOURCE 100
- Setting remote control codes 101
- Remote control features 102
- Programming codes from other 103
- Changing source names in the 104
- Macro programming features 105
- ■ Default macro functions 106
- 2 Press the 107
- 4 Press 107
- Clearing configurations 108
- ■ Clearing a macro function 109
- ■ Using external amplifiers 110
- Controlling Zone 2 or Zone 3 111
- 3 Press 112
- (except Europe model) 114
- Advanced setup 115
- Troubleshooting 119
- ADDITIONAL 121
- INFORMATION 121
- DEVICE OVER 122
- HDCP ERROR 122
- Resolution 122
- ■ Remote control 123
- ■ AUTO SETUP 124
- Resetting the system 126
- Glossary 127
- ■ PCM (Linear PCM) 130
- ■ S-video signal 130
- ■ Frequency 132
- ■ Q factor 132
- Specifications 133
- Фронтальная панель 140
- Afstandsbediening/Пульт ДУ 141
- HD DVD PLAYER 144
- Blu-lay Disc player 144
- APPENDIX 147
- Printed in Malaysia 151
Produits connexes et manuels pour Récepteurs AV Yamaha RX-V1800
Récepteurs AV Yamaha YHT-S401 Manuel
(70 pages)
(70 pages)
Récepteurs AV Yamaha RX-V767 Manuel
(133 pages)
(133 pages)
(538 pages)
Récepteurs AV Yamaha HTR-4063 Manuel
(97 pages)
(97 pages)
(58 pages)
Récepteurs AV Yamaha RX-V650 Manuel
(91 pages)
(91 pages)
© 2020, manymanuals.fr. Tous droits réservés | 2.103 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels