Yamaha RX-V665 Manuel Page 20

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 148
  • Table des matières
  • DEPANNAGE
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 19
18 En
Connections
An indoor FM antenna and an AM loop antenna are
supplied with this unit. Connect these antennas properly to
the respective jacks.
y
The supplied antennas are normally sensitive enough to obtain good
reception.
Position the AM loop antenna away from this unit.
If you cannot get good reception, we recommend that you use an outdoor
antenna. For more details, consult the nearest authorized Yamaha dealer
or service center.
Always use the AM loop antenna even when the outdoor antenna is
connected.
Assembling the AM loop antenna
Connecting the AM loop antenna
The wires of the AM loop antenna have no polarity. You
can connect either wire to the AM terminal and the other
to the GND terminal.
Select the switch position according to your local voltage
using a straight slot screwdriver.
[General model]
Voltages are AC 110/120/220/230-240 V, 50/60 Hz.
[Asia model]
Voltages are AC 220/230-240 V, 50/60 Hz.
After all connections are complete, plug the AC power
cable of this unit into an AC wall outlet.
1 Press AMAIN ZONE ON/OFF (or
gPOWER) to turn on this unit.
2 Press AMAIN ZONE ON/OFF (or
gPOWER) again to turn off this unit
(standby mode).
y
The unit needs a few seconds until ready to play back.
You can also turn on this unit by pressing JSCENE (or lSCENE).
This unit consumes a small amount of electricity even in the standby
mode. We recommend disconnecting the power cable from the AC wall
outlet.
Connecting the FM and AM antennas
ANTENNA
UNBAL.
FM
GND
AM
PH
O
N
O
G
ND
DOC
K
CO
MP
O
NENT
V
IDE
O
P
R
P
B
Y
V
IDE
O
H
DM
I
HDMI
1
(
B
D
/
DV
D
)
HDMI
2
HDMI
3
H
V
IDE
O
IN
OU
T
M
O
NIT
O
R
OUT
TRI
GG
ER
OU
T
1
2
V
0
.1
A
MAX.
FR
O
CENTER
P
R
P
B
Y
REM
O
T
E
CO
MP
O
NEN
T
VIDEO
O
U
T
Outdoor AM antenna
Connect a 5 to 10 m (16 to
33 ft) vinyl-covered wire,
and extend it outdoors
(use the AM loop antenna
together with this
antenna).
Ground (GND terminal)
The GND terminal is not for earth grounding.
To reduce noises, connect a ground bar or a
vinyl-covered wire with a copper plate at its tip,
and place it in the moist ground.
Indoor FM antenna
AM loop
antenna
Press and hold ReleaseInsert
Connecting the power cable
VOLTAGE SELECTOR (Asia and General
models only)
Caution
The VOLTAGE SELECTOR on the rear panel of this
unit must be set for your local voltage BEFORE
plugging the power cable into the AC wall outlet.
Improper setting of the VOLTAGE SELECTOR may
cause damage to this unit and create a potential fire
hazard.
Connecting the AC power cable
Turning this unit on and off
Caution
Do not unplug this unit while it is turned on. Doing so
may damage this unit or cause the settings of this unit
to be saved incorrectly.
230-
240V
VOLTAGE
SELECTOR
Voltage indication
Vue de la page 19
1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 147 148

Commentaires sur ces manuels

Pas de commentaire