Yamaha RX-V371 Manuel du propriétaire télécharger pdf (Page 24)

En 24

CONNECTIONS

Set up the speaker parameters automatically (YPAO)

■

Message list

■ When a warning message appears before

measurement

■ Error message

■ Warning message

NOTE

If the following messages appear, resolve the problems that have

occurred and carry out the measurement process again.

Connect MIC! The YPAO microphone is

not connected.

Connect the YPAO

microphone to the YPAO

MIC jack on the front

panel.

Unplug PHONES! The headphones are

connected.

Remove the headphones.

Memory Guard! The settings of this unit

are protected.

Set “Memory Guard” in

the Setup menu to “Off.”

E-1:FRONT SP The unit was not able to

find the front channel.

Check that the left and

right front speakers are

connected correctly.

E-2:SUR. SP The unit was only able to

find one of side of the

surround channels.

Check that the left and

right front surround

speakers are connected

correctly.

E-5:NOISY The noise is too loud,

preventing accurate

measurements from

being taken.

Measure again in quiet

surroundings. Turn off any

devices in the room that

may be emitting noise, or

place them further away

from the YPAO

microphone.

When this message is

displayed, selecting

“Proceed” will allow you

to continue measuring.

However, we recommend

resolving the problem and

measuring again, as

continuing measurement

without doing so will not

give accurate results.

E-7:NO MIC The YPAO microphone

has been removed.

While measuring, take

care not to touch the

YPAO microphone.

E-8:NO SIGNAL The YPAO microphone

could not distinguish a

test tone.

Check that the YPAO

microphone has been

installed correctly.

Check that each speaker

has been connected and

installed correctly.

The YPAO microphone

or the YPAO MIC jack

may be broken. Inquire at

the retailer where you

purchased this unit, or the

nearest Yamaha service

center.

E-9:CANCEL You have carried out an

operation that has

cancelled the measuring

process.

Carry out the measuring

process again. Do not

operate this unit by, for

example, adjusting the

volume.

E-10:INTERNAL An internal error has

occurred.

Turn off and on this unit,

and carry out the measuring

process again. Contact a

Yamaha service center if

“E-10” appears again.

W-1:PHASE The speakers displayed

are connected with the

opposite polarity.

Depending on the type of

speakers you are using

and the environment in

which you have them

installed, this message

may occur even if the

speakers are connected

correctly.

Depending on the type of

speakers, “W-1” may

display even if the

speakers are connected

correctly.

Check that the speaker

polarity + (plus), and -

(minus) are correct. If

these are connected

correctly, you can use the

speakers normally even

this message appears.

W-2:OVER 24m

(80ft)

The speakers displayed

are separated from the

listening position by

more than 24m, and

cannot be adjusted

correctly.

Install the speakers with

24m of the listening

point.

W-3:LEVEL The difference each

channel is too loud or too

low, and cannot be

adjusted correctly.

Check that all speakers

are installed in the same

surroundings.

Check that the speaker

polarity + (plus), and -

(minus) are correct.

We recommend the same

speakers or speakers with

as similar specifications

as possible.

Adjust the volume of the

subwoofer.

If “W-2” or “W-3” appears, you can apply measurement results,

but they will not give optimal results. We recommend that you

resolve the problem and carry out the measurement process

again.

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 67 68

Commentaires sur ces manuels

Pas de commentaire

Yamaha RX-V371 Manuel du propriétaire Page 24

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs AV Yamaha RX-V371