Yamaha RX-V1 Manuel du propriétaire Page 24
- Page / 95
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
20
Preparations
Connecting Speakers
This section explains how to connect speakers to the RX-V1. After you finish connecting your speakers, use the SET MENU to change the
signal output settings according to the number and size of the speakers in your configuration.
■ Using Speaker Cords
A speaker cord is actually a pair of insulated cables running side by side. One of
the cables is colored or shaped differently, perhaps with a stripe, groove or ridge.
To make sure you always connect speakers with the correct polarity, determine
the difference between the cables of your speaker cord, make a note of which
cable you plan to use for which polarity (+ and –), and always connect the speaker
cords consistently.
1
1
Strip off 9 mm (3/8 in.) of an inch of insulation from the ends of the
cables.
2
2
Twist the exposed wires of the cable together to prevent short
circuits.
3
3
Loosen the terminal knob by turning it counterclockwise.
4
4
Insert only the exposed portion of the cable into the slot in the side of
the terminal, and tighten the terminal knob.
Note:
• If your speaker cords have banana plugs, tighten the terminal knob and insert the
plug into the end of the terminal.
Caution:
• Connect the speaker cords with care to avoid creating a short circuit. If you turn on
the power and there is a short circuit, this unit may be damaged even though the
protection circuit automatically shuts off the power.
■ Connecting the Main Speakers
Before connecting any speaker cords, identify which terminals are for the right
and left channels and also the + and – polarities. If you connect speakers with the
wrong polarity (+ to –), the RX-V1 will not reproduce clear sound.
Connect the + and – terminals of your right and left Main speakers to
the L and R MAIN + and – terminals on this unit.
■ Connecting the Center Speaker
Connect the + terminal of your Center speaker to the CENTER +
terminal and the – terminal of your Center speaker to the CENTER –
terminal.
Hookups
AMAINB
+
–
+
–
+
–
SPEAKERS
FRONT
REAR
CENTER REAR CENTER
+
–
+
–
+
–
+
–
+
–
+
–
BANANA PLUG
Right Main
Speaker A
Left Main
Speaker A
Right Main
Speaker B
Left Main
Speaker B
Center Speaker
- SAFETY INSTRUCTIONS 2
- EXAMPLE OF ANTENNA GROUNDING 3
- Contents 5
- Introduction 6
- Features 7
- Checking the Package Contents 9
- Front Panel 10
- Controls and Functions 11
- Remote Control 12
- Front Panel Display 14
- Rear Panel 15
- Preparations 16
- Speaker System Configurations 17
- Speaker Placement 18
- About the Video Jacks 19
- Connecting to Digital Jacks 19
- Connecting Audio Components 20
- ■ Connecting a Tape Deck 21
- Connecting Video Components 22
- ■ Connecting a VCR 23
- ■ Connecting a DVD Player 23
- ■ Connecting a Video Monitor 23
- Connecting Speakers 24
- SPLIT jacks using pin plugs 25
- ■ Connecting a Rear Subwoofer 26
- ■ Impedance Selector switch 26
- (SURROUND) 27
- Connecting Power Supply Cords 28
- Connecting the Antennas 29
- OSD Modes 30
- Selecting the OSD Mode 30
- Before You Begin 31
- Dolby Surround Test 32
- DSP Test 33
- Basic Operation 34
- Power Control 35
- Selecting a Source 36
- Input Modes and Indications 37
- Basic Playback 38
- Manual Tuning 39
- Automatic Tuning 39
- Presetting Stations 40
- AM/FM Tuner 41
- Tuning to Preset Stations 42
- Exchanging Preset Stations 42
- Advanced Operation 44
- SET MENU Items 45
- Operating the SET MENU 46
- 2. LOW FREQ. TEST 50
- 4. DTS SET 52
- 5. SP DELAY TIME 52
- 6. AUDIO DELAY 52
- 9. CINEMA EQ 54
- 12. 6.1/ES AUTO 55
- 13. MEMORY GUARD 56
- 15. INPUT MODE 56
- 16. INPUT RENAME 57
- 17. DIMMER 57
- 18. ZONE 2 SET 57
- Using the Remote Control 58
- Remote Control Features 59
- Each Component Control Area 60
- A / B / C / D / E PRESET 61
- A / B / C / D / E 61
- Advanced 62
- Operation 62
- V-AUX TAPE PHONO 65
- D-TV CBL/SAT TUNER MD CD 65
- VCR 1 VCR 2 VCR 3 LD DVD 65
- Using the Macro Feature 67
- ■ Operating the Macro Feature 68
- ■ Programming a Macro 68
- Manufacturer Setups 70
- ON SCREEN 71
- SLEEP TEST 71
- Connections 72
- Remote Control in ZONE 2 73
- Additional Information 74
- Understanding Sound Fields 75
- Recreating a Sound Field 75
- E/R (Early Reflection) 75
- Hi-Fi DSP-Sound Field Program 76
- CINEMA-DSP 77
- Movie Theater Programs 78
- ■ Program Groups 7~9 79
- ■ Program Groups 10~12 79
- Changing Parameter Settings 81
- EFCT TRIM (Effect Trim) 82
- INIT. DLY (Initial Delay) 82
- S. DLY (Surround Delay) 83
- ROOM SIZE 83
- LIVENESS 84
- Appendix 86
- Troubleshooting 87
- Specifications 92
- V482920-1Printed in Japan 93
- Quick Reference Card 94
Produits connexes et manuels pour Récepteur Yamaha RX-V1
(15 pages)
Récepteur Yamaha RX-V4600 Manuel du propriétaire
(126 pages)
(126 pages)
Récepteur Yamaha V150 Manuel du propriétaire
(104 pages)
(104 pages)
Récepteur Yamaha RX-V1600 Manuel du propriétaire
(132 pages)
(132 pages)
Récepteur Yamaha RX-V861 Manuel du propriétaire
(129 pages)
(129 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.078 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels