Yamaha AW2400 Manuel d'utilisateur

Recording 101 Yamaha Corporation of America 6600 Orangethorpe Ave. Buena Park, CA 90620 USA Customer Support: 714-522-9000 Y

5. Cursor to OK and press the [ENTER] key. The TITLE EDIT popup window will appear, allowing you to name your song. 6. Assign a name to yo

The IN 1-8 is for input 1-8 and IN 9-16 is for input 9-16. 4. Select the meter section to show the input meter screen by pressing the [METER

3. In the Quick Navigate section press the [RECORD] key until the DIRECT page of the RECORD screen is displayed.

4. Raise the fader of the track that you are recording on to the 0 mark and

Punch In/Out If you make a mistake while recording, you can punch-in at the spot that the mistake was made. To punch-in simply means to start r

Disengaging a track from being record-enabled 1. In the Quick Navigate section press the [RECORD] key until the DIRECT page of the RECORD

2. While playing the instrument, turn the GAIN knob up to adjust the input level. The meter on the right side of the Input Setting screen should be

The selected input channel will now be connected to the selected track. Both the selected [INPUT SEL] key and the selected [

Mixdown Once all of the tracks are recorded it is time to begin the mixdown process. Mixdown is the process of mixing the individual recorded track

164. Start with the drum tracks (or rhythm tracks) and raise the faders until the L R meters read around -12 to -6 dB. When you are finished, the o

ii AW2400 Recording 101 - Table of Contents Introduction 1 AW2400 Features 1 Setting up the AW2400 2 Connecting the

Adjusting the Panning 1. Press the [TRACK SEL] key of the track that you wish to adjust the panning for. 2. Press the [PAN/EQ SEL] key until the

according to how you would actually hear them if you were facing a set of drums. For example, the low tom would be panned to the left while the hi-ha

For example, if you listen to a track and feel that it is not clear enough instead of adding EQ in the high end you may be better off taking out some

A dynamics processor may also be used to expand the dynamic range of a track. If a track lacks dynamic range, you can use an expander. An example of

Using the Internal Effects Processors After applying EQ and dynamics processing to the tracks you may want to use the internal effects of the AW240

5. While playing the song, cursor to the send knob of the track that you want to send to the first effects unit, and then use the jog wheel to adju

1. In the Quick Navigate section, repeatedly press the [RECORD] key until the MIXDOWN screen is displayed. 2. Move the cursor to the REC bu

Creating an Audio CD After the Stereo Track is recorded you can create an audio CD of the song. 1. Insert a blank CD-R in the CD-RW drive of th

The AW2400 automatically selects the first stereo track on the hard drive. It does NOT automatically select the stereo track that was just recorde

26Glossary Note: Additional glossary words can be found online at the following web address: http://solutionsnetwork.yamaha.com A/D Converter: Anal

iiiUsing the EQ Library 18 Adjusting the Dynamic Processors 19 Using the Dynamics Library

27Dynamics Processor: A signal processing device that is used to correct or control signal levels. They are able to compress, expand, compress-expand

Introduction Congratulations on your purchase of the AW2400! The AW2400 is a very powerful and easy to use digital audio workstation that will a

Setting up the AW2400 Before you begin recording it is necessary to connect the AW2400 with the equipment that it is to be used with. Step 1: Conn

Do not use speaker cable to connect the AW2400 to the power amp. If no monitors are available, or if you prefer, headphones can be used for monitori

Either microphones or devices such as keyboards or drum machines can be connected to inputs 1-8. If a condenser microphone is to be connected,

This will prevent damage to the speakers. If the monitoring system is turned on first, then when the AW2400 and the other equipment is turned on a lo

2. Move the cursor to the NEW button and press the [ENTER] key next to the jog wheel. A popup window will ask you if you want to save the curren