Yamaha 01V96 Manuel d'utilisateur

1 Configure Your Yamaha Console To MIDI Control The Waves SG MultiRack System March 6, 2013

10 4.0 - Setup YAMAHA M7CL/LS9/CL Series (CL5/CL3/CL1) MIDI Connections Technical Note: When using Ethernet connection between Yamaha M7CL/LS9/CL Se

11 2. Under the MIDI SETUP tab, set the PORT/CH under the Tx column to MIDI and set it to CH1. 3. Switch the PROGRAM CHANGE and CONTROL CHANGE, und

12 M7CL SCENE MEMORY section CL Series SCENE MEMORY section LS9 DATA ENTRY section On the LS9 Click on SCENE MEMORY under DISPLAY

13 4.2 - Setup the M7CL/LS9/CL Series MIDI Control Change Settings: The Yamaha M7CL/LS9/CL Series consoles do not have the MIDI REMOTE functionality

14 3. A green edit window will appear, named MIDI CONTROL CHANGE [#103]. 4. Under MODE column select MIX/MATRIX SEND. 5. Under PARAMETER1 column s

15 5.0 - Setup YAMAHA DM1000/2000 and O1V96/O2V96 MIDI / USB Connections Follow these instructions to setup the required MIDI/USB connections to con

16 5. Set the MIDI PORTS in this page. a. If MIDI is used, set the Tx MIDI PORT to MIDI, and set REMOTE under SPECIAL FUNCTIONS also to MIDI. b.

17 Yamaha O1V96 SCENE MEMORY Control Yamaha DM1000 SCENE MEMORY Control This concludes the programming on your Yamaha DM1000/2000 console.

18 6.0 - Configure Your SG MultiRack System for MIDI Control: Please follow these instructions to configure your SG MultiRack system for MIDI Contro

19 2. In the Control tab, check the required MIDI In port: a. The MAC Address of the WSG-Y16 card is shown, and should be selected if a MIDI cable

2 Table of Contents Welcome to the Yamaha/Waves Midi Control Manual ... 3 1.0 - The Pos

20 3. The selection box for Set MIDI channel for snapshot recall under MIDI Snapshot Recall should match the Channel number used for MIDI Tx on the

21 7.0 – Mapping the MultiRack Remote Controller Editor Window In this section we'll cover the MIDI Mapping of MultiRack's Remote Controll

22 5. Click on Open Editor to open the MultiRack Remote Controller Editor Window. There you will see a fully configured MIDI messages mapped to the

23 7.2 – Manual Mapping of the MultiRack Remote Controller Editor Window: Once you have the Yamaha console MIDI Control fully configured, it is very

24 4. Repeat this process until you have completed configuring all the functions you want to control via the Yamaha Console. 5. Once a MIDI message

25 Please Note : When setting the SNAPSHOT RECALL Section, bear in mind that when you are use the Yamaha console Scene Control, the MultiRack Snapsho

26 8.0 Implementing the Yamaha Console MIDI mapping with the SG MultiRack: In your SG MultiRack’s session you will be able to see which plug-ins par

27 The Plug-in parameters which are assigned to MIDI Controllers will be highlighted Red as shown below. Furthermore, the Plug-ins Parameter Page nu

28 Appendix A. Remote control assignments of Yamaha PM5D, DM2000, DM1000 consoles. A.1 – Plug-in and Racks Parameters Control. This will cover wh

29 A.2 - MIDI functions Assigned to User Defined Keys of these Yamaha consoles. This will cover the MIDI functions are assigned to the User Defined

3 Welcome to the Yamaha/Waves Midi Control Manual The following range of Yamaha digital mixers have the ability to interface with Waves to remotely

30 B. Remote control assignments of Yamaha M7CL, LS9 and CL Series consoles. This will cover which of the following functions will be controlled by

4 2. Connect a USB cable between the Yamaha Console USB out port and the Computer running your SoundGrid MultiRack software. USB link from PM5D-RH

5 3.0 - Setup YAMAHA PM5D MIDI / USB Connections 3.1 – Setup the required MIDI/USB connections: Follow these instructions to setup the required MID

6 b. If MIDI is used, set the MIDI PORT under the Tx column to USB Port 3. Set MIDI REMOTE Output Port for BANK A to USB Port 2, as shown below. 5.

7 3.2 - Setup the PM5D MIDI Remote Settings: Technical Note : The initial settings for the PM5D MIDI Remote are not suitable for controlling SG Mult

8 To load the file from a Memory Card follow these instructions : 1. Insert the Memory Stick to the designated slot on your console. 2. Access the

9 2. Under ENCODER ON and CH ON make sure the Latch is highlighted. 3. Under ENCODER ON, ENCOUDER, CH ON and FADER, should be setup to transmit Co