Yamaha DSP-Z9 Manuel du propriétaire Page 87
- Page / 122
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
85
English
REMOTE CONTROL FEATURES
ADVANCED
OPERATION
■ Macro operations
1 Set MACRO ON/OFF to ON.
2 Press a macro button.
• When you have finished using the macro feature, set MACRO
ON/OFF to OFF.
• While the remote is carrying out a macro program, it will not
accept any other button’s function until the macro operation is
complete (the TRANSMIT indicator stops flashing).
• Continue to aim the remote control at the component the macro
is operating until the macro operation is complete.
■ Programming macro operations
You can program your own macros and use the macro
feature to transmit several remote control commands in
sequence at the press of a button. Be sure to set up
manufacturer codes or perform learning operations before
programming the macro. We do not recommend
programming continuous operations such as volume
control in a macro.
• The default macro is not cleared when a new macro is
programmed for a button. The default macro can be used again
when the programmed macro is cleared.
• It is not possible to add a new signal (macro step) to the default
macro. Programming a macro changes all macro contents.
1 Press MACRO using a ballpoint pen or
similar object.
“MCR ?” appears in the display window.
y
Complete each of the following steps within 30 seconds.
Otherwise, the learning mode is automatically canceled. In
this case, press MACRO again.
2 Press the macro button you want to use to
operate the macro.
The macro button name and the selected component
name appear alternately in the display window.
• “AGAIN” appears in the display window if you press a button other
than a macro button.
• To change the selected source component, press SOURCE SELECT
k/n. Pressing the input selector buttons will program a macro step,
whereas SOURCE SELECT k/n only changes the selected
component and corresponding component control area.
3 Press the buttons for the functions you want
to include in the macro operation in
sequence.
You can set up to 10 steps (10 functions). After you
have set 10 steps, “FULL” appears and the remote
control automatically exits from the macro mode.
“NG” appears in the display window if programming was
unsuccessful. In this case, start over from step 2.
Notes
Notes
TRANSMIT
RE-NAME
STANDBY
TUNER
MULTI CH IN
PURE DIRECT
SYSTEM
CLEAR LEARN MACRO
OFF ON
MACRO
PHONO
CD
DVD
DVR
VCR 2
TITLE
DTV/LD
VCR 1
CD-R
MD/TAPE
SAT
CABLE
POWER
V-A UX
MACRO
MACRO ON/OFF
Macro buttons
MACRO
Notes
Note
TUNER
PHONO
CD
DVD
DVR
VCR 2
DTV/LD
VCR 1
CD-R
MD/TAPE
SAT
CABLE
V-A UX
Flashes alternately
STANDBY
TUNER
MULTI CH IN
PURE DIRECT
TOP EXIT
INPUT MODE
SOUND
SYSTEM
PHONO
CD
DVD
DVR
VCR 2
TITLE
MENU
CHAPTER
PAUSE
STOP
POWER
REC
SELECT
DISPLAY
SEARCH
SOURCE
PLAY
–+
ENTER
DTV/LD
VCR 1
CD-R
MD/TAPE
SAT
CABLE
POWER
V-A UX
1
2
MCR 1: DVD a
MCR 2: DVD h
Indicates the
number of macro
steps entered
Flashes alternately so you can
set the next step
00EN.00_DSPZ9_GB.book Page 85 Thursday, November 13, 2003 10:55 AM
- AV Amplifier 1
- Amplificateur Audio-Vidéo 1
- ■ For U.K. customers 2
- CONTENTS 3
- FEATURES 4
- GETTING STARTED 5
- Notes on batteries 6
- ■ GUI remote control 6
- CONTROLS AND FUNCTIONS 7
- GUI remote control 10
- Using the remote controls 11
- Front panel display 12
- Rear panel 13
- SPEAKER SETUP 14
- Speaker connections 15
- Bi-wired connection 17
- This unit 17
- CONNECTIONS 18
- Connecting video components 19
- MULTI CH INPUT 20
- PREPARATION 21
- Cable TV tuner 22
- Audio out 22
- Video out 22
- Optical out 22
- A B C D E F 24
- Connecting audio components 26
- POWER AMP IN 28
- POWER AMP INPOWER AMP IN 28
- ■ AC OUTLET(S) (SWITCHED) 29
- ■ VOLTAGE SELECTOR 29
- (General model only) 29
- ■ Memory back-up 29
- Speaker impedance setting 30
- Turning on the power 30
- USING THE GUI REMOTE CONTROL 31
- MULTI CH IN 32
- PURE DIRECT 32
- TOP EXIT 32
- INPUT MODE 32
- AUTO SETUP 33
- Starting the setup 34
- Confirming the results 36
- Before auto setup 37
- During auto setup 37
- After auto setup 38
- PLAYBACK 39
- DialNorm;;+4dB 40
- JAZZ CLUB 41
- Village Gate 41
- ■ Enjoying 2-channel software 43
- 2ch Stereo 44
- Front panel Remote control 45
- Front panel 45
- Remote control 45
- Selecting input modes 46
- Remote control operation 47
- RECORDING 48
- DTS software 49
- For movie/video sources 50
- Program Features Sources 51
- For music sources 53
- ADVANCED OPERATIONS 55
- Using the test tone 56
- SYSTEM OPTIONS 57
- ■ Auto Setup (Auto setup) 58
- ■ Memory Guard (Memory Guard) 58
- ■ Signal Info. (Signal Info.) 58
- Changing parameter settings 59
- Input Select 60
- ■ Rename (Rename) 61
- ■ Volume Trim (Volume trim) 61
- ■ Assign (Assign) 61
- ■ Analog Level (Analog level) 62
- ■ BGV (Background video) 62
- Manual setup: Sound 63
- ■ Tone Control (Tone control) 64
- Manual setup: Basic 66
- ■ THX Set (THX settings) 67
- ■ Speaker Set (Speaker set) 69
- Manual setup: Video 73
- ■ Picture Mode (Picture mode) 74
- ■ Resolution (Resolution) 74
- ■ Aspect (Aspect) 75
- ■ Aspect conversion examples 76
- ■ Cross Color (Cross color) 76
- ■ TV Format (TV format) 76
- Manual setup: Option 77
- ■ Input Mode (Input mode) 78
- ■ Display (Display) 79
- ■ Multi Zone (Multi zone) 79
- Memory Guard 80
- ■ Manual Setup (Manual setup) 81
- Control area 82
- Setting manufacturer codes 83
- Programming codes from other 84
- Changing source names in the 85
- Using the macro feature 86
- ■ Macro operations 87
- Clearing function sets 88
- Clearing individual functions 89
- Controlling components 90
- ■ Operating an LD player 91
- ADVANCED 93
- OPERATION 93
- STRAIGHT 94
- Zone 2 connections 95
- Remote controlling Zone 2 96
- USING i.LINK 98
- Assigning i.LINK components 99
- Changing i.LINK Select 100
- ■ Information (Information) 101
- ■ Select (Select) 101
- ■ Auto Play (Auto Play) 101
- Status display messages 102
- Error messages 102
- SOUND FIELD OPTIONS 103
- Stereo/Surround menu 105
- 60 dB 60 dB 106
- ■ Decode Type (Decoder type) 109
- For THX Cinema 109
- For Surround Enhanced 109
- For Surround Standard 109
- For Movie Theater Programs 109
- TROUBLESHOOTING 110
- ADDITIONAL 111
- INFORMATION 111
- ■ Remote control 113
- ■ Frequency 114
- ■ Q factor 114
- GLOSSARY 115
- ■ THX MUSIC MODE 118
- ■ THX Ultra2 118
- ■ THX Surround EX 118
- BLOCK DIAGRAMS 119
- ■ Video matrix 120
- ■ Power supply 120
- SPECIFICATIONS 121
Produits connexes et manuels pour Récepteur Yamaha DSP-Z9
Récepteur Yamaha RX-A810 Spécifications
(15 pages)
(15 pages)
(15 pages)
Récepteur Yamaha RX-V4600 Manuel du propriétaire
(126 pages)
(126 pages)
Récepteur Yamaha V150 Manuel du propriétaire
(104 pages)
(104 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.261 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels