Yamaha S30 Manuel du propriétaire télécharger pdf (Page 44)

44

Basics

Section

1 Press the [UTILITY] key to enter Utility

Mode.

2 Use the [PAGE] knob to switch to the CTRL

Other (System Control Other) screen.

3 Use Knob [B] to select “099:PC Inc”

(Program Change Increment).

In Voice/Performance Mode, the Foot Switch

can now be used to switch between programs.

Alternatively, you can assign other functions

such as Arpeggio Switch (On/Off),

Sequencer (Play/Stop) and so on (Page 129).

Using Knob [1]/[2] To Control the Arpeggio

You can assign Arpeggiator ON/OFF and

Hold functions to Knob [1]/[2] (Performance

Mode). The following is an explanation of

how to do this. In the example, we use

Internal Performance 075 (E11), and assign

Arpeggio Hold to Knob [1] and Arpeggio

ON/OFF to Knob [2].

1 Press the [UTILITY] key to enter Utility

Mode.

2 Use the [PAGE] knob to switch to the MIDI

Arp screen.

SHIFT PAGE

PA RT

/

ELEMENT

DATAABC1 2

CTRL Other) FS

Sys 099[PC Inc ]

SHIFT PAGE

PA RT

/

ELEMENT

DATAABC1 2

CTRL Other) FS

Sys 088[ ------ ]

STOREVOICE

M

ODE

UTILITY

EDIT JOB

PLAY

/

STOP

CARD

SEQ

PLAY

PERFORM

COMPARE

3 Use Knob [B] to assign the Control Change

Number for Arpeggio ON/OFF, which is 90

here. Similarly, use Knob [C] and set the

Control Change Number to 89 to assign

Arpeggio Hold to Knob [1].

4 Press the [PERFORM] key to enter

Performance Mode.

5 Select Internal Performance 075 (E11), then

enter Performance Edit Mode by pressing

the [EDIT] key.

6 Turn Knob [A] until “Common” is

displayed at the bottom left of the screen.

7 Use the [PAGE] knob to switch to the CTL

Assign1 screen.

8 Turn Knobs [1]/[2] to set their parameters

to the same values as the Control Change

Numbers set in Step 3. That is, assign a

value of 89 to Knob [1] and a value of 90 to

Knob [2].

9 Store the edited Performance (Page 124).

Now, for Internal Performance 075 (E11),

Arpeggio Hold is assigned to Knob [1] and

Arpeggio ON/OFF to Knob [2]. If you select

this Performance in Performance Play Mode,

turning each knob left or right will switch its

respective parameter off or on, respectively.

(The Arpeggiator responds to notes below C3

on the keyboard.)

If you do not wish to control the Destination

parameter of the Voice, enter Performance

Edit Mode, switch to the RCV Sw2 screen of

Performance Part Edit, then set the

parameters for Knobs [1] and [2] to “off.”

In Performance Mode, to use the Arpeggiator

for Parts which have their Layer parameter

(Layer Switch) set to “on,” their Arp

parameter (Arpeggio Switch) also has to be

set to “on.” (Page 117)

SHIFT PAGE

PA RT

/

ELEMENT

DATAABC1 2

CTLíAssign1) BC Knob1 Knob2

Common [FootCtrl] 02 89 90

SHIFT PAGE

PA RT

/

ELEMENT

DATAABC1 2

MIDI Arp) Switch Hold Out(Vce)Ch(Vce)

Sys[ ] 90 89 off 16

1 2 ... 39 40 41 42 43 44 45 46 47 48 49 ... 155 156

Commentaires sur ces manuels

Pas de commentaire