Yamaha 303 Manuel d'utilisateur télécharger pdf (Page 195)

Using Your Instrument with Other Devices

CVP-305/303/301 Owner’s Manual

195

MIDI Settings

● Tx MONITOR

The dots corresponding to each channel (1–16) ﬂash

brieﬂy whenever any data is transmitted on the chan-

nel(s).

When different parts are assigned to the same transmit

channel

If the same transmit channel is assigned to several different parts,

the transmitted MIDI messages are merged to a single channel—

resulting in unexpected sounds and possible glitches in the con-

nected MIDI device.

About the protected Songs

Write-protected Songs and GS songs cannot be transmitted even if

the proper Song channels 1–16 are set to be transmitted.

■ MIDI messages which can be transmitted or

received (recognized)

The following MIDI messages can be set on the TRANS-

MIT/RECEIVE display.

• Note (Note events).......................................page 154

• CC (CONTROL CHANGE) ..........................page 154

• PC (PROGRAM CHANGE)...........................page 154

• PB (Pitch Bend)............................................page 154

•AT (Aftertouch).............................................page 154

MIDI Receive Settings

The explanations here apply to the RECEIVE display to

be called up in step 4 of the “Basic Operation” on

page 192. This determines which parts will receive

MIDI data and over which MIDI channels the data will

be received.

Operation

Select the channel to be received and the part via which

the selected channel will be received. You can also

determine the types of data to be received.

● The Clavinova can receive MIDI messages over

32 channels (16 channels x 2 ports) by USB con-

nection.

● With the exception of the two parts below, the

conﬁguration of the parts is the same as those

already explained elsewhere in this manual.

• KEYBOARD

The received note messages control the Clavinova’s

keyboard performance.

• EXTRA PART 1–5

There are ﬁve parts specially reserved for receiving

and playing MIDI data. Normally, these parts are not

used by the instrument itself. The Clavinova can be

used as a 32-channel multi-timbral tone generator by

using these ﬁve parts in addition to the general parts

(except for the microphone sound).

● Rx MONITOR

The dots corresponding to each channel (1–16) ﬂash

brieﬂy whenever any data is received on the channel(s).

n Parameter Lock

You can “lock” speciﬁc parameters (e.g., effect, split

point, etc.) to make them selectable only via the panel

controls (page 122).

■ MIDI transmission/reception via the USB ter-

minal and MIDI terminals

The relationship between the [MIDI] terminals and the

[USB] terminal which can be used for transmitting/

receiving 32 channels (16 channels x 2 ports) of the

MIDI messages is as follows:

Setting the Bass Note for Style Playback

via MIDI Receive

The explanations here apply to the BASS display to be

called up in step 4 of the “Basic Operation” on

page 192.

These settings let you determine the bass note for Style

playback, based on the note messages received via

MIDI. The note on/off messages received at the chan-

nel(s) set to “ON” are recognized as the bass note of the

chord of Style playback. The bass note will be detected

regardless of the [ACMP ON/OFF] or split point set-

tings. When several channels are simultaneously set to

“ON,” the bass note is detected from merged MIDI data

received over the channels.

RECEIVE display

MIDI/USB1

01–16

USB2

01–16

USB2USB1

Merge

MIDI/USB 01–16

Port

handling

[MIDI IN] jack

MIDI reception MIDI transmission

[USB TO

HOST] jack

[MIDI OUT] jack

[USB TO

HOST] jack

BASS display

1 2 ... 190 191 192 193 194 195 196 197 198 199 200 ... 219 220

Commentaires sur ces manuels

Pas de commentaire

Yamaha 303 Manuel d'utilisateur Page 195

Commentaires sur ces manuels

Produits connexes et manuels pour Instruments de musique Yamaha 303