Yamaha A-S1100 Manuel du propriétaire

ABIntegrated AmplifierOWNER’S MANUAL© 2015 Yamaha CorporationPrinted in Malaysia ZQ25570

10 EnControls and functions Rear panel1 PRE OUT jacksy• The PRE OUT jacks output the same channel signal as the SPEAKERS L/R CH terminals.• When you

11 En0 MAIN IN jacksUse these jacks to connect an external component equipped with a volume control.yWhen you select MAIN DIRECT as the input source,

12 EnControls and functions Remote control1 Infrared signal transmitterOutputs infrared control signals.2 p AMP keyTurns this unit ON or switches it

13 En5 CD player control keysControl various functions of Yamaha CD player. Refer to the owner’s manual of your CD player for details.p CD key: Turns

14 EnControls and functions Installing batteries in the remote control1 Remove the battery compartment cover.2 Insert the two batteries (AAA, R03, UM

ConnectionsIn this section, you will make connections between A-S1100, speakers,and source components.

16 EnConnections• Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could damage this unit

17 En• Because the power amplifier of A-S1100 is of the floating balanced type, the following types of connections are not possible.– Connecting with

18 EnConnections Connecting the speakers1 Remove approximately 10 mm of insulation from the end of each speaker cable and twist the exposed wires of

19 En Bi-wire connectionThe bi-wire connection separates the woofer from the combined midrange and tweeter section. A bi-wire compatible speaker has

2 EnA Living Tradition in SoundA piano comes into this world through the perfect synergy of advanced technical skill and artistry. Such a piano can cr

20 EnConnections Operating this unit from another roomIf you connect an infrared receiver and transmitter to the REMOTE IN/OUT jacks of this unit, yo

21 En Connecting a component supporting the trigger function such as a Yamaha AV receiverThe operations of this unit can be controlled in synchroniza

22 En

20Hz 1kHz 20kHz20Hz1kHz20kHzAppendixIn this section, you will find technical specifications for A-S1100.

24 EnAppendixSpecificationsPOWER SECTION• Rated Output Power[U.S.A, Canada, Taiwan, China, Korea, Australia, U.K. and Europe models] (L/R, 8 , 20 Hz

25 En Block diagram LINE2 OUT PHONO INPUT SELECTOR PRE OUTMM//MCFLOATING & BALANCESPEAKER DRIVERMOS FETFLOATING & BALANCESPEAKER DRIVERMOS FE

26 EnAppendix Tone control characteristics Total harmonic distortion10 20 30 50 100 200 300 500 1kFrequency (Hz)Relative Level (dB)2k 3k 5k 10k 20k

27 En Total harmonic distortion (PHONO)100µ 200µ 500µ 1m 2m 5m 10m 20mGenerator Level (Vrms)50m 100m 200m 500m 1 220Hz 1kHz 20kHz1052310.50.20.30.020

28 EnAppendixTroubleshootingRefer to the chart below if this unit does not function properly. If the problem you are experiencing is not listed below

29 EnProblem Cause RemedySee pageA “humming” sound is heard.Incorrect cable connections. Connect the audio cable plugs firmly. If the problem persists

3 EnNP-S2000Soavo-1NS-10MA-S3000CD-S3000NS-20CA-1000NS-690B-1PX-2C-2NS-1000MA-1B-6B-2xMX-10000CX-10000Excellence in Audio AchievementFirst HiFi System

ABIntegrated AmplifierOWNER’S MANUAL© 2015 Yamaha CorporationPrinted in Malaysia ZQ25570

4 En◆ Floating & Balance power amplifier circuit◆ Parallel volume and tone control◆ Large power supply with four separate circuits◆ Left-right sy

5 EnControls andfunctionsIn this chapter, you will learn the controls and functions of A-S1100.

CONTROLS AND FUNCTIONS6 EnControls and functions Front panel (pages 6 to 9)1 STANDBY/ON, OFF switchTurns on or off this unit.STANDBY/ON (upper positi

7 En4 SPEAKERS selectorTurns on or off the sets of speakers connected to the SPEAKERS L/R CH A and/or B terminals on the rear panel, as follows.OFF: B

8 EnControls and functions Front panel (pages 6 to 9)0 Remote control sensorReceives signals from the remote control.A INPUT selector/indicatorSelect

9 EnB AUDIO MUTE switchPress downward to reduce the current volume level by approximately 20 dB. Press again to restore the audio output to the previo