Yamaha RAPTOR 700R SE Manuel d'utilisateur télécharger pdf

Dyna FS Ignition DFS 7-21P

2006+ Yamaha Raptor 700R

9,100 RPM LIMIT (9,000 stock YFM700R)

CAUTION: This ignition can increase the engine rev-limiter! The stock fuel injection limits at 9,000RPM

Congratulations on your purchase of a Dynatek ignition. Please take a moment to read these instructions completely before

installing the ignition. The installation will only take about one half hour, but proper setup for your specific bike may take longer.

The DynaFS ignition is designed to work with the stock coil, coil wire, plug cap, and spark plug. Use the stock resistor style spark

plug cap. For additional spark energy, use the Dyna Coil Kit DCK7-1.

This kit includes: DynaFS ignition, Curve Selector Switch, electrical wiring, cable ties and instruction sheet. This is a complete kit,

and includes everything needed to install the ignition.

Note:

Route all wires carefully. Secure wires in factory loops or use the supplied cable-ties to ensure electrical wires do not chafe or

touch anything sharp or hot.

Installation

1) Turn ignition key off. It is not necessary, but recom

mended to remove the front plastics and fuel tank to make routing of the

electrical harness easier.

2) The DynaFS ignition for the Raptor 700R was designed to fit in the document/tool tray area behind the airbox, under the seat.

Find a suitable location if this area has been changed.

3) The DFS electrical harness has two parts. The first part: ground, pickup and TPS(yellow) harness was designed to route

along the left side of the airbox, to the battery and left side of the engine.

a) Connect the black ground wire (with eyelet) to battery ground.

b) Crank position sensor wires are on the left side, above the starter motor and behind the throttle body. Wire colors are

Blue/Yellow and Black/Blue. Unplug the two position WHITE connector with these colors. Plug the white connectors

to the Dyna ignition, forming a “Y” intercept. (see pictures 1, 2)

c) Connect yellow Dyna wire to yellow wire at the Throttle Position Sensor (right side of throttle body) using the supplied

T-Tap connector. Unplug the TPS connector. Unwind electrical tape at TPS connector. Cut a one inch slice in the

protective sleeve, to expose the yellow wire. Place T-Tap connector over yellow wire. Close T-Tap on wire using pliers.

Plug on yellow Dyna wire. Reposition sleeve, and re-tape. Plug the TPS connector back onto the TPS sensor. (see

pictures 3, 4, 5)

4) The second part of the electrical harness: coil intercept and power wires get routed along the left side of the airbox, then

across the frame behind the fuel tank, then along the right side of the frame up to the ignition coil.

a) Disconnect the Orange wire from the ignition coil negative and connect it to the DFS orange wire. Plug the DFS

Orange/Black wire onto the ignition coil negative. (see pictures 6, 7 ,8)

b) Disconnect the Red/Black wire (Switched +12V) from the ignition coil positive, and install the DFS Red/Black

piggyback spade connector onto the ignition coil positive, connect the Raptor Red/Black wire onto the DFS piggyback

terminal.

c) The DFS – BLACK/WHITE wire is an extra KILL INPUT for connecting an aftermarket Tether Switch for racing.

Ground this input to activate.

d) The DFS - PURPLE wire is for activating the two-step launch limiter (RPM must be programmed in Dynatek Curve

Maker). Ground to activate low-side limiter.

5) Zip-tie loose harness or accessory wires to the frame. Use the supplied velcro to mount the ignition.

6) Plug in the Curve Selector Switch. Mount the Curve Selector Switch in desired location. You may want to mount it so

that it is easily accessible for initial tuning.

Do not

cut or lengthen the wires

DYNATEK

164 S. Valencia St., Glendora, CA 91741 800-928-3962 www.dynaonline.com

2801312C

1 2 3 4 5 6

Résumé du contenu

Page 1 - Dyna FS Ignition DFS 7-21P

Dyna FS Ignition DFS 7-21P 2006+ Yamaha Raptor 700R 9,100 RPM LIMIT (9,000 stock YFM700R) CAUTION: This ignition can increase the engine rev-limite

Page 2 - WARNING:

DYNATEK 164 S. Valencia St., Glendora, CA 91741 800-928-3962 www.dynaonline.com 2801312C Calibration The DynaFS is programmed with 4 advance curve

Page 3 - (CRANKSHAFT DEGREES)

THROTTLEPART- RETARD(STOCK)CURVE4CURVE2ADVANCEDCURVE1CURVE3WIDE OPENTHROTTLE (Curves 1-4)DYNA FS / YAMAHA RAPTOR 700R - IGNITION CURVESCU

Page 4 - 2801312C

4 wires terminated with female bullet connectors3-position connector for Curve Selector Switch4-position connector for PC/Laptop programmingPURPLE =

Page 5

Picture1: Battery Ground. Picture2: Crank Pickup intercept connectors. Picture3: Expose the Yellow TPS signal w

Page 6

Picture5: Re-Tape the TPS connection. Picture6: Coil connections to stock ignition coil. Picture7: Coil connections to Dynatek C

Commentaires sur ces manuels

Pas de commentaire

Yamaha RAPTOR 700R SE Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Véhicule tout-terrain Yamaha RAPTOR 700R SE. Raptor 700R Dyna FS Ignition (06-10) Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Véhicule tout-terrain Yamaha RAPTOR 700R SE