Yamaha DTXPRESS IV Manuel d'instructions Page 2
- Page / 2
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Mounting the pads and the trigger module on the
rack system
Mount the pads and the trigger module on the rack system. Then position the
kick pad and the hi-hat.
Mounting the TP65 (Drum pads) and TP100 (3-zone Drum pad)
on the rack system
Figure 10: Pads Assembly-1 Figure 11: TP65 and TP100
!1
TP100
!2
TP65 (Rear side)
!3
TP100 (Rear side)
!4
Clamp bolt
1 See Figure 11.
Attach the clamp bolts (
!4
) on TP65s (
!2
) and TP100 (
!3
). Tighten the clamp bolts ve to six
turns each.
Figure 12: Pads Assembly-2
2 See Figure 12. Loosen the knobs of the tom holders and at the center of the rack
system (shown with
). Move the tom holders as shown in Figure 12-(a). Then tighten the
knobs and x the position of the tom holders
and .
3 Loosen the knob of the tom holder on the right (shown with ). Move the tom holder
inward as shown in Figure 12-(b). Tighten the knobs and attach the tom holder rmly at a
position where it points slightly downward.
Figure 13: Tom Holder and Drum Pad
!5
Tom holder
!6
Clamp bolt
4 Attach the TP65 (Drum pad) to the tom holder as shown in Figure 13. Tighten the clamp
bolt and attach the drum pad TP65 rmly.
5 See Figure 12 again. Repeat step 3 and 4 in the same manner for tom holder at the
center of the rack system and for tom holder
on the right, and attach the TP65 (Drum
pad) to each tom holder.
6 Loosen the knobs of the snare holder on the left (shown with ). Turn the snare holder
as shown with the big arrow in Figure 12-(c) and set it up vertically. Turn the metal stick
on the upper part of
as shown with the small arrow in Figure 12-(c) until it is pointing
slightly outward than pipe
.
7 Attach the 3-zone drum pad TP100 to the snare holder set up in step 6. Tighten the
clamp bolt and attach the 3-zone drum pad TP100 rmly.
Mounting the PCY135 and PCY155 (Cymbal pads)
on the rack system
Figure 14: Pads Assembly-3 Figure 15: Cymbal holder-1
@1
PCY155
@2
Cymbal holder
@3
Wing nut
@4
Felt washer
1 See Figure 15.
Remove the wing nut (
@3
) and the two felt washers (
@4
) from the cymbal holder (
@2
). Then
turn the black plastic part in a counterclockwise direction and remove it.
Figure 16: Cymbal holder-2 Figure 17: Cymbal holder-3
@5
Stopper
@6
Drum key
@7
Key bolt
2 See Figure 16. Attach the stopper to the cymbal holder, and x at a position where the
L-shaped part of the stopper is on the opposite side from you. To x the position of the
stopper (
@5
), use the drum key (
@6
) and tighten the key bolt (
@7
) rmly.
3 See Figure 17. Attach the black plastic part removed in step 1 to the cymbal holder, and
tighten it in a clockwise direction.
4 Attach one of the felt washers removed in step 1 to the cymbal holder. The other felt washer
will not be used within the standard assembly described in this manual.
Figure 18: Cymbal holder and Cymbal pad
5 See Figure 18. Insert the end of the L-shaped part of the stopper into the oval-shaped hole
on the cymbal pad (shown with
) to set the cymbal pad on the cymbal holder.
* Cymbal pad PCY135 is very similar to Real High-Hat Pad RHH135. Check the part num-
ber on the reverse side.
6 Attach the included round-shaped felt with a large hole-diameter to the cymbal holder,
then attach the wing nut removed in step 1 and tighten it. Turn the wing nut until you are
certain that the cymbal pad is attached. The cymbal pad is designed to shake when you hit
the surface, even when the wing nut is tightened securely.
Mounting the DTXP4 (Trigger module)
Figure 19: Pads Assembly-4 Figure 20: Module stand
@8
Wing nut
@9
Module stand
#0
DTXP4 (Rear side)
1 Attach the module stand (
@9
) onto the rear side of the DTXP4 (
#0
) using the wing nuts (
@8
).
Figure 21: Module stand and clamp
#1
DTXP4 + Module stand
#2
Clamp
#3
Knob
2 Attach the module stand (
#1
) onto the clamp (
#2
). Tighten the knob (
#3
) and x the
position.
Assembling the KP65 (Kick pad)
1 If a drum mat (sold separately) is not available, lay a cardboard on the oor to prevent
scratching the surface.
Figure 22: KP65 Assembly
#4
Body
#5
Base
#6
Wing bolt
#7
Spring washer
#8
Washer
2 Remove the wing bolt (
#6
), the spring washer (
#7
) and the washer (
#8
) from the body (
#4
),
and keep the four sets nearby in the order removed.
* If the wing bolt, the spring washer and/or the washer are separated from each other, set
them as illustrated in Figure 22-(a).
3 Set the base (
#5
) on the body (
#4
), and attach them using the wing bolt, the spring washer
and the washer removed in step 2.
Assembling the HS650A (Hi-Hat stand)
1 If a drum mat (sold separately) is not available, lay a cardboard on the oor to prevent
scratching the surface.
Figure 23: HS650A Assembly
$1
Radius rod
$2
Hi-Hat clutch
$3
Felt washer
$4
Cymbal support plate
$5
Cymbal support
2 Loosen the wing bolt of the hi-hat stand (shown with in Figure 23-(a)).
3 Spread out the legs of the tripod part of the hi-hat stand until it stands stable. Tighten the
wing bolt loosened in step 2.
4 Insert the radius rod (
$1
) into the hole of the frame as shown in Figure 23-(b).
5 Loosen the wing bolt of the hi-hat clutch (
$2
) (shown with in Figure 23-(c)).
* The hi-hat clutch is not used within the standard assembly described in this manual. Use
the hi-hat clutch included in RHH135.
6 Pull out the hi-hat shaft from pipe .
7 Insert the hi-hat shaft removed in step 6 into the nut shown in Figure 23-(c).
8 Insert pipe into the hi-hat shaft from above. Tighten the wing bolt at the position
where the cymbal support plate will be positioned at the middle area of the hi-hat shaft
.
9 Remove the felt washer (
$3
) and the cymbal support plate (
$4
) attached above the cymbal
support plate. They are not used within the standard assembly described in this manual.
10 Set the real hi-hat pad RHH135.
* For the next step, see "Setting Up" in the RHH135 Owner's manual.
Installing the Hi-Hat and KP65 (Kick pad)
Figure 24: Hi-Hat and KP65
1 If a drum mat (sold separately) is not available, lay
a cardboard on the oor to prevent scratching the
surface.
2 Place the hi-hat (
%1
) on the left side of the RS85 (Rack
system).
3 Place the KP65 (Kick pad) (
%2
) at the bottom center of
the rack system.
%1
Hi-Hat
%2
KP65 (Kick Pad)
Connecting the pads to the Trigger Module
Connect the output jacks of the pad and the input jacks of the trigger module
with the 9-channel snake cable.
Figure 25: DTXP4 (Rear panel)
Figure 26: 9-channel Snake Cable
* Each straight plug is labeled indicating the input jacks to which they are to be connected.
1 Insert the straight plugs (Figure 26-(a)) of the 9-channel snake cable into the input jacks on
the rear panel of the trigger module. For standard assembly, connect the straight plugs to
the input jacks in accordance with the indication on each label.
Figure 27: Diagram of standard connection
SNARE
KICK
em
%3
Stereo phone cable
2 Insert the L-shaped plugs (Figure 26-(b)) of the 9-channel snake cable into each
corresponding pad. It is recommended to connect the cables in order from numbers
q
to
o
shown in Figure 27 (from the shortest cable to the longest cable).
3 Insert the L-shaped plug end of the stereo phone cable into the cymbal pad PCY135 (
!0
in
Figure 27). Insert the straight plug end of the stereo phone cable into the PAD IN jack of Kick
pad KP65 (
!1
).
Connecting to a power source
Connect the AC adaptor to the DTXP4.
Figure 28: Power switch (DTXP4 rear panel)
^1
Power supply jack (DC IN 12V)
^2
Cable clip
^3
Power switch
1 Make sure to turn the power o (the Standby/
On switch (
^3
) is set to the standby position
(
)).
Figure 29: Cable clip (DTXP4 rear panel)
2 Attach the AC adaptor to connect to a power
source.
Insert the DC plug into the power supply jack
(
^1
) and twist the cable around the cable clip
(
^2
) to prevent the DC plug from falling out.
Figure 30: Using Cable Band
3 Use the cable bands to bind the cables to the
pipes at the six points shown with the circles.
* Leaving the cable slacked may inter-
fere with your performance.
The assembly is now completed.
* To check the actual sound, connect the unit with an ampli ed speaker or a headphone before turning on the
power.
U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation
©2009 Yamaha Corporation
WS41240
********.*-****
Printed in Indonesia
DTXPRESS_SP-set_en_0407.indd 2DTXPRESS_SP-set_en_0407.indd 2 2009/04/07 10:56:322009/04/07 10:56:32
1
2
Produits connexes et manuels pour Instruments de musique Yamaha DTXPRESS IV
(16 pages)
(13 pages)
(89 pages)
(98 pages)
(32 pages)
(32 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.624 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels