Yamaha IMX644 Manuel du propriétaire

Owner's ManualENLST0803-001B 008AP-02B0© 2008 Yamaha CorporationU.R.G., Pro Audio DivisionYamaha Pro Audio global web site:http://www.yamahapro

Controls and Functions10 IMX644 Owner’s ManualNOTE• Refer to “Connectors and Cables” on page 13 for details on connectors and cables for use with

Controls and FunctionsIMX644 Owner’s Manual 119 [+48V] SwitchWhen ON, 48V phantom power is applied to the corresponding mono input. Turn the [+48V

12 IMX644 Owner’s ManualConnectionsSystem Example1 2 3 45 6 7 8ComputerCD recorderPower amplifierPower amplifierExternal control input/output device

ConnectionsIMX644 Owner’s Manual 13 [MONO INPUT] and [OUTPUT] Con-nectors (3-pin Euroblock)Connect external microphones, amplifiers and other dev

Connections14 IMX644 Owner’s Manual3 Securely tighten the terminal screws.Pull the cables (not too strongly) to confirm that they are securely conn

IMX644 Owner’s Manual 15Mix FunctionsThe IMX644 mix functions can be programmed and edited in detail using the IMX644 Manager installed on a compu

Mix Functions16 IMX644 Owner’s Manual Feedback SuppressorThe Feedback Suppressor effectively controls feedback by iden-tifying the feedback frequ

Mix FunctionsIMX644 Owner’s Manual 17 OUTPUT EQThe parameters of the independent 6-band parametric equalizers provided for OUTPUT channels 1 thro

18 IMX644 Owner’s ManualAppendixThe following procedure initializes the IMX644 memory.CAUTION• All data stored in memory will be erased when the m

AppendixIMX644 Owner’s Manual 193 To recall the initial memory data press a MEMORY button for longer than two seconds.NOTE• Initialization erases

The above warning is located on the top of the unit. Explanation of Graphical Symbols The lightning flash with arrowhead symbol within an equilateral

Appendix20 IMX644 Owner’s ManualThe commands that can be transferred between the IMX644 and a remote controller are as follows.<Command> <

AppendixIMX644 Owner’s Manual 21ANALOG INPUT CHARACTERISTICS* 0dBu = 0.775 Vrms. , 0dBV = 1.00 Vrms.* +48V DC( phantom power ) is supplied to MONO

Appendix22 IMX644 Owner’s ManualOutput impedance of signal generator : 150 ohmsFrequency Response20Hz-20kHz, reference to the nominal output level

AppendixIMX644 Owner’s Manual 23 Example: Controlling the IMX644 from a switch Example: Lighting the LED of an external device from the IMX644

Appendix24 IMX644 Owner’s Manual* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves

AppendixIMX644 Owner’s Manual 25Block Diagram+48VMONO 1 - 6ON+48VAD+-INPUT GAINSIGNALPEAK1233BANDPEQLEVELF. B .SUPTO OUT1TO OUT2OUT 1A(L) BUSOUT 1

Information for Users on Collection and Disposal of Old EquipmentThis symbol on the products, packaging, and/or accompanying documents means that used

For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below.CANADAYamaha Canada Music Ltd.13

Owner's ManualENLST0803-001B 008AP-02B0© 2008 Yamaha CorporationU.R.G., Pro Audio DivisionYamaha Pro Audio global web site:http://www.yamahapro

(5)-6 1/2 IMX644 Owner’s Manual 3 PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future re

(5)-6 2/2 4 IMX644 Owner’s Manual • Before connecting the device to other devices, turn off the power for all devices. Before turning the powe

IMX644 Owner’s Manual 5 Table of contents Introduction Features ...

6 IMX644 Owner’s Manual Introduction Thank you for purchasing the Yamaha IMX644 Digital Installation Mixer. In order to take full advantage of t

Introduction IMX644 Owner’s Manual 7 This unit will operate stably in an environmental temperature of 0–40˚C. If you install this device togethe

8 IMX644 Owner’s Manual Controls and Functions1 [LOCK] Switch and Indicator The [LOCK] switch can be used to “lock” the panel level knobs (5, 8,

Controls and Functions IMX644 Owner’s Manual 9 MONO INPUT Section3 Matrix Indicators The outputs to which each mono input are assigned are dis