DYNATEK IGNITION with EFI REV-EXTEND
(P/N DFS7-29 FOR 2007-2008 YAMAHA GRIZZLY 700 EFI)
(P/N DFS7-30 FOR 2009+ YAMAHA GRIZZLY 700 EFI)
8,500 RPM LIMIT (7,300 stock Grizzly 700)
CAUTION: This ignition will increase the engine rev-limiter!
Congratulations on your purchase of a Dynatek ignition. Please take a moment to read these instructions completely before
installing the ignition. The installation will only take about thirty minutes, but proper setup for your specific vehicle may take
longer. The DynaFS ignition was designed to work best with the Dynatek coil kit DCK7-5(2007 models) or DCK7-8(2008+
models) or stock coil with the stock coil wire, plug cap, and spark plug. Always use the stock resistor style spark plug cap and a
resistor spark plug.
Description
The DYNATEK Ignition Module for the Yamaha Grizzly 700efi is a piggyback add-on device that will increase the performance
of the stock ignition and fuel injection system. This Module is designed to work in conjunction with the stock ECU, and will take
complete control of the Ignition Timing while safely extending the fuel injection rev-limit. With the optional Dynatek
CurveMaker software or the Dynatek DRSP-1 remote serial programmer, the ignition curves, fuel maps, rev-limits, and vehicle
speed limits can be custom tailored for any application.
Installation
This kit includes: DynaFS ignition, electrical wiring, velcro, cable tie-wraps and instruction sheet. This is a complete kit, and
includes everything needed to install the ignition. Route all wires carefully. Secure wires using the supplied cable-ties to ensure
electrical wires do not chafe or touch anything sharp or hot.
1. Turn ignition key off. Remove the right side plastics and snorkel. Use the supplied velcro to install the ignition in the
preferred location, right side of fuel tank (picture 1).
2. Connect the Pickup Intercept and Vehicle Speed Intercept (both located on the right side of engine, near the starter
motor) by unplugging the stock connectors and connecting the matching DFS harness connectors in-line (picture 2).
3. Connect the Throttle Position Intercept (right side of throttle body) and Fuel Injector Intercept (top of engine) by
unplugging the stock connectors and connecting the matching DFS harness connectors inline. It is very difficult to reach
the TPS connector, and may require removal of the airbox assembly to reach these connectors. Route the harness
carefully using the supplied tie-wraps (picture 3).
4. Route the Coil Connections Harness towards the coil. Connect the Ignition Coil Intercept (at the ignition coil terminals)
by removing the stock ORANGE wire (coil negative) and connecting it to the DFS ORANGE wire (picture 4).
5. For 2007 models with black connector at coil +12V: USE PICTURE 5
Connect the Ignition +12V stock BROWN/RED wire (black plastic connector) to the DFS piggyback spade
connector, and then re-connect the joined terminals to the left side of the coil, ensure this connection is tight. Now,
using the supplied Orange adaptor wire, Connect the DFS Ignition Coil Output ORANGE/BLACK wire to this
adaptor, and the other end to the right side ignition coil negative input.
5. For 2008+ models with 90° rubber connector at coil +12V: USE PICTURE 6
Connect the DFS Ignition Coil Output ORANGE/BLACK wire to the ignition coil negative input. Connect the
Ignition +12V Piggyback by removing the stock RED/BLACK 90° terminal and installing the DFS piggyback spade
connector the coil positive, and then re-connecting the stock +12V lead to the DFS piggyback terminal.
6. Connect the DFS BLACK GROUND wire under the 8mm bolt at the back of the starter motor, directly under the
throttle body. This can be easily seen from the right side of the vehicle (picture 4).
7. Finally, tie-wrap the DFS Accessory Wires away from the engine and away from sharp objects.
8. Now is a good time to start the vehicle and check that the vehicle idles properly.
9. Installation is complete! Reinstall snorkel and body plastics. Double-check your wiring and secure all loose wires
using tie-wraps.
DYNATEK
164 S. Valencia St., Glendora, CA 91741 800-928-3962 www.dynaonline.com
2801402A
(178 pages)
(32 pages)
(108 pages)
(44 pages)
(44 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels