Yamaha DPX-1 Manuel télécharger pdf (Page 20)

E-17

English

Menu structure

■ 4 <SETUP>

Menu item

INSTALLATION

There are four methods to install this unit; tabletop or on-ceiling for front or rear projection. The image can

be inverted or rotated according to the setting for the installation method.

SCREEN ASPECT

Selects 4:3 or 16:9 depending on the screen to be used. If 16:9 is selected, vertical adjustment of the image

can be made by changing the value of the item “DIGITAL LENS SHIFT”. And automatically makes an

adjustment to project the 4:3 input signal without losing any part of it off screen.

* DIGITAL LENS SHIFT

The image on the screen can be vertically adjusted within a certain range by digital processing. h moves the

image upward and g downward. This adjustment is available only when the screen aspect ratio is set to 16:9.

KEYSTONE

If this unit projects on a the screen with some elevation or depression angle at its installation, the image on

the screen is distorted into a trapezoid. This parameter electrically corrects the distortion. Increase the value

when the upper part of the image is wider. Decrease the value when the lower part if the image is wider.

KEYSTONE MODE

There are two modes; “FULL” that corrects the key stone effect without changing the vertical length of the

image, and “NORMAL” that makes vertical correction by shifting the bottom at the same time. Select the

appropriate mode to make correction depending on your installation.

R/C SENSOR

Sets the remote control sensor to be used. This unit has its remote control sensor in two locations: at the front

and the rear.

Choice/adjustment range

FRONT/TABLE, FRONT/CEILING,

REAR/TABLE, REAR/CEILING

4:3/16:9*

–96 to 96

–128 to 127

NORMAL/FULL

FRONT&REAR/FRONT/REAR

■ 3 <INITIAL>

Menu item

COLOR SYSTEM

Selects the color system when the video signal is input among NTSC, NTSC4.43, PAL, PAL-M, PAL-N,

PAL60, SECAM. AUTO should normally be selected so that the appropriate color system can be

automatically selected depending on the input signal. However, PAL-M should be selected when the

input signal is PAL-M.

INPUT A SIGNAL

Selects the type of input signal sent to the INPUT A jacks.

INPUT B SIGNAL

Selects the type of input signal sent to the INPUT B jacks.

LANGUAGE

Selects the language used on the menu.

POWER SAVING

When no signal is received at the input jacks for longer than 15 minutes, this unit automatically turns off

the lamp and enters the standby mode if ON is selected.

LAMP RUNNING TIME

Displays the total lamp running time. The lamp running time can be reset on the submenu.

RESET

Resets all parameters on the menu or parameters in the memory to the factory settings.

Choice

AUTO/NTSC/NTSC4.43/PAL/PAL-M/PAL-N/

PAL60/SECAM

COMPONENT/RGB PC/RGB TV

/ENGLISH/DEUTSCH/ESPAÑOL/

FRANÇAIS/ITALIANO/

OFF/ON

—

ALL SETTINGS/ALL MEMORIES/

CURRENT MEMORY

1Normal correction

This correction shifts the bottom of the projected image to correct

the horizontal distortion.

When the upper part of the image is wider than the

lower part, increase the value to the positive (+)

direction.

When the lower part of the image is wider than the

upper part, decrease the value to the negative (–)

direction.

2Full correction

This correction adjusts the horizontal distortion without changing

the vertical length of the projected image.

When the upper part of the image is wider than the

lower part, increase the value to the positive (+)

direction.

When the lower part of the image is wider than the

upper part, decrease the value to the negative (–)

direction.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 38 39

Commentaires sur ces manuels

Pas de commentaire

Yamaha DPX-1 Manuel Page 20

Commentaires sur ces manuels

Produits connexes et manuels pour Projecteurs de données Yamaha DPX-1