Yamaha RX-V665 Manuel du propriétaire Page 16
- Page / 94
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
12 En
Connections
■ Connecting to the FRONT, CENTER,
SURROUND and SURROUND BACK/BI-AMP
terminals
1 Remove approximately 10 mm (0.4 in) of
insulation from the end of each speaker
cable and then twist bare wires of the cable
together so that they will not cause a short
circuits.
2 Loosen the knob, insert the twisted bare
wires into the hole, and then tighten the
knob.
■ Connecting to the EXTRA SP terminals
1 Press down the tab and insert the bare end of
the speaker cable into the hole in the terminal.
y
• You can connect the presence speakers (see page 11) or the speakers in
the second zone (Zone2) (see page 57) to EXTRA SP terminals.
2 Release the tab to secure the wire.
You can connect speakers that support bi-amplification
connections to this unit. Before connecting the speakers,
set this unit to enable bi-amplification connections in
“ADVANCED SETUP” (see page 60), and connect the
speakers to this unit as shown below.
Connecting the speaker cable
Caution
• A speaker cable is a pair of insulated cables running side by side in general. One of the cables is colored differently
or striped to indicate a polarity. Connect one end of the colored/striped cable to the “+” (red) terminal of this unit
and the other end to that of your speaker, and connect one end of the other cable to the “–” (black) terminal of this
unit and the other end to that of your speaker.
• Before connecting the speakers, be sure to disconnect the power cable.
• Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or
speakers. If the circuit shorts out, “CHECK SP WIRES!” appears on the front panel display when this unit is turned
on.
• Use magnetically shielded speakers. If images on the monitor are still distorted even when you use the magnetically
shielded speakers, place the speakers away from the monitor.
• Use speakers with an impedance of 6-ohm or larger. Set speaker impedance in “ADVANCED SETUP” before
connecting the speakers (see page 60).
Connecting the banana plug (Except U.K.,
Europe, Asia and Korea models)
Tighten the knob, and then insert the banana plug into
the end of the terminal.
10 mm (0.4 in)
1
2
3
Red: positive (+)
Black: negative (–)
Banana plug
Using bi-amplification connections
Caution
Before making bi-amplification connections, remove
any or cables that connect a woofer with a tweeter.
Refer to the instruction manuals of speakers for details.
When not making bi-amplification connections, make
sure that the brackets or cables are connected before
connecting the speaker cables.
Red: positive (+)
Black: negative (–)
SURROUND BACK/
BI-AMP
FRONT
Front speakers
Right Left
This unit
- AV Receiver 1
- IMPORTANT SAFETY INSTRUCTIONS 3
- Caution-ii En 4
- Contents 5
- INTRODUCTION 6
- About this manual 7
- Supplied accessories 7
- Part names and functions 8
- Rear panel 9
- Front panel display 10
- Remote control 11
- Quick start guide 12
- PREPARATION 13
- Connections 14
- Connecting speakers 15
- Connecting the speaker cable 16
- R) components 17
- TV, or projector 18
- Digital output 18
- (optical) 18
- Connecting other components 19
- MULTI CH INPUT 20
- Connecting the power cable 22
- Turning this unit on and off 22
- Subwoofer 23
- Optimizer microphone 23
- BASIC OPERATION 26
- Straight 28
- For movie/TV program sources 29
- Program name 29
- Sound field program category 29
- For audio music sources 30
- For stereo reproduction 30
- The Compressed Music Enhancer 31
- Surround decode mode 31
- FM92.5MHz 33
- Auto Preset 33
- 01:FM87.5MHz 33
- 01:FM92.5MHz 34
- (sold separately) 35
- 001Preview 36
- 00880's 36
- P01:---<<008 37
- 008 80's 37
- Back to “Channel” 38
- 184Weather 39
- 001Hits1 40
- P01:---<<001 41
- 001 Hits 1 41
- Setting the Parental Lock 42
- Radio™ information 43
- Using iPod™ 44
- Shuffle/repeat playback 45
- Using Bluetooth™ components 46
- ADVANCED OPERATION 47
- Signal Info parameters 48
- Video;;;;HDMI1 49
- Sound field program 50
- Sound field parameters 50
- Set values 50
- CINEMA DSP basic parameters 50
- Dialog Lift 51
- Decoder parameters 53
- ;SpeakerSetup 55
- LFE/Bass Out 56
- Front SP 56
- Center SP 56
- Sur. L/R SP 56
- Sur.B L/R SP 56
- Sound Setup 57
- Function Setup 58
- 2 Display 59
- 3 Volume 59
- 4 Input Rename 59
- DSP Parameter 60
- Memory Guard 60
- Connecting Zone2 61
- Controlling Zone2 62
- Setting remote control codes 63
- ADVANCEDSETUP 64
- APPENDIX 65
- Troubleshooting 66
- Tuner (FM/AM) 68
- Bluetooth™ 72
- Before Auto Setup 73
- During Auto Setup 73
- After Auto Setup 74
- Glossary 75
- Information on HDMI™ 78
- Specifications 79
- List of remote control codes 82
- Blu-ray Disc 88
- DVD Recorder 88
- Sattelite 89
- Printed in China WQ95310 92
- ■ Front panel 93
- Printed in China 94
Produits connexes et manuels pour Récepteurs AV Yamaha RX-V665
Récepteurs AV Yamaha RX-V1400 Manuel
(92 pages)
(92 pages)
Récepteurs AV Yamaha NS-P270 Manuel
(40 pages)
(40 pages)
(244 pages)
Récepteurs AV Yamaha R-V1103 Manuel
(59 pages)
(59 pages)
Récepteurs AV Yamaha RX-797 Manuel
(83 pages)
(83 pages)
Récepteurs AV Yamaha HTR-5790 Manuel
(90 pages)
(90 pages)
Récepteurs AV Yamaha DSP-AX1 Manuel
(88 pages)
(88 pages)
© 2020, manymanuals.fr. Tous droits réservés | 3.697 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels